markdowned-datasheets/REN_RAA489400/07-registers.md at master

0m.ax 920097c3ad add REN_RAA489400

2026-08-23 15:14:22 +02:00

95 KiB

Raw Permalink Blame History

7. Registers

Table 6. Register Attributes

Attribute	Abbreviation	Description
Read/Write	`R/W`	Read/Write
Read Only	`R`	Read Only (Write1/0 ignore)
Write Only	`W`	Write Only
Read. Write 1 Clear	`R/W1C`	Read. Write 1 Clear (Write 0 ignore)

7.1 Register Map

Table 7. Register Map

Address	Register Name	Register Table	Type	Reset Value
TCPC Standard Registers
`00h...01h`	`VENDOR_ID`	Table 8	R	`045Bh`
`02h...03h`	`PRODUCT_ID`	Table 9	R	`026Dh`
`04h...05h`	`DEVICE_ID`	Table 10	R	`0100h`
`06h...07h`	`USBTYPEC_REV`	Table 11	R	`0021h`
`08h...09h`	`USBPD_REV_VER`	Table 12	R	`3115h`
`0Ah...0Bh`	`PD_INTERFACE_REV`	Table 13	R	`2012h`
`0Ch...0Fh`	Reserved as TCPCI specification	-	-	-
`10h...11h`	`ALERT`	Table 14	R/W	`0200h`
`12h...13h`	`ALERT_MASK`	Table 15	R/W	`6FFFh`
`14h`	`POWER_STATUS_MASK`	Table 16	R/W	`DFh`
`15h`	`FAULT_STATUS_MASK`	Table 17	R/W	`BFh`
`16h`	`EXTENDED_STATUS_MASK`	Table 18	R/W	`01h`
`17h`	`ALERT_EXTENDED_MASK`	Table 19	R/W	`01h`
`18h`	Reserved as TCPCI specification	-	-	-
`19h`	`TCPC_CONTROL`	Table 20	R/W	`00h`
`1Ah`	`ROLE_CONTROL`	Table 21	R/W	`0Ah` or `0Fh`
`1Bh`	`FAULT_CONTROL`	Table 22	R/W	`00h`
`1Ch`	`POWER_CONTROL`	Table 23	R/W	`62h`
`1Dh`	`CC_STATUS`	Table 24	R	`00h`
`1Eh`	`POWER_STATUS`	Table 25	R	`48h`
`1Fh`	`FAULT_STATUS`	Table 26	R/W	`80h`
`20h`	`EXTENDED_STATUS`	Table 27	R	`01h`
`21h`	`ALERT_EXTENDED`	Table 28	R/W	`00h`
`22h`	Reserved as TCPCI specification	-	-	-

Table 7. Register Map (Cont.)

Address	Register Name	Register Table	Type	Reset Value
`23h`	`COMMAND`	Table 29	W	`00h`
`24h...25h`	`DEVICE_CAPABILITIES_1`	Table 31	R	`7EDDh`
`26h...27h`	`DEVICE_CAPABILITIES_2`	Table 32	R	`C2C3h`
`28h`	`STANDARD_INPUT_CAPABILITIES`	Table 33	R	`02h`
`29h`	`STANDARD_OUTPUT_CAPABILITIES`	Table 34	R	`00h`
`2Ah`	Reserved as RAA489400	-	-	-
`2Bh`	Reserved as TCPCI specification	-	-	-
`2Ch...2Dh`	Reserved as RAA489400	-	-	-
`2Eh`	`MESSAGE_HEADER_INFO`	Table 35	R/W	`04h`
`2Fh`	`RECEIVE_DETECT`	Table 36	R/W	`00h`
`30h`	`READABLE_BYTE_COUNT`	Table 37	R	`00h`
`30h`	`RX_BUF_FRAME_TYPE`	Table 38	R	`00h`
`30h`	`RX_BUF_BYTE_x`	Table 39	R	`00h`
`50h`	`TRANSMIT`	Table 40	R/W	`00h`
`51h`	`I2C_WRITE_BYTE_COUNT`	Table 41	W	`00h`
`51h`	`TX_BUF_BYTE_x`	Table 42	W	`00h`
`70h...71h`	`VBUS_VOLTAGE`	Table 43	R	`0000h`
`72h...73h`	`VBUS_SINK_DISCONNECT_THRESHOLD`	Table 44	R/W	`008Ch`
`74h...75h`	`VBUS_STOP_DISCHARGE_THRESHOLD`	Table 45	R/W	`0020h`
`76h...77h`	`VBUS_VOLTAGE_ALARM_HI_CFG`	Table 46	R/W	`0000h`
`78h...79h`	`VBUS_VOLTAGE_ALARM_LO_CFG`	Table 47	R/W	`0000h`
`7Ah...7Bh`	Reserved as RAA489400	-	-	-
`7Ch..7Dh`	`DEVICE_CAPABILITIES_3`	Table 48	R	`0006h`
`7Eh...7Fh`	Reserved as TCPCI specification	-	-	-
RAA489400 Vendor Defined Registers
`80h`	`CHIP_REV`	Table 49	R	`12h`
`81h`	Reserved	-	-	-
`82h`	`GPIO1_CTRL`	Table 50	R/W	`00h`
`83h`	`GPIO2_CTRL`	Table 51	R/W	`00h`
`84h`	`GPIO3_CTRL`	Table 52	R/W	`00h`
`85h`	`GPIO4_CTRL`	Table 53	R/W	`00h`
`86h`	`VBUS_PATH_CTRL`	Table 54	R/W	`00h`
`87h`	`VBUS_GPIO_CTRL`	Table 55	R/W	`00h`
`88h`	`VBUS_CP_CTRL`	Table 56	R/W	`00h`
`89h`	`GPIO_OC_EN`	Table 57	R/W	`00h`
`8Ah…8Fh`	Reserved	-	-	-
`90h…91h`	`VBUS_CTRL`	Table 57	R/W	`0001h`
`92h…93h`	`VBUS_CURRENT`	Table 58	R	`0000h`

Table 7. Register Map (Cont.)

Address	Register Name	Register Table	Type	Reset Value
`94h…95h`	`VBUS_PEAK_CURRENT`	Table 60	R	`0000h`
`96h…97h`	`VBUS_AVE_CURRENT`	Table 61	R	`0000h`
`98h`	`FRS_CTRL`	Table 62	R/W	`40h`
`99h`	Reserved	-	-	-
`9Ah`	`SINK_PATH_DISCHG_CTRL`	Table 63	R/W	`00h`
`9Bh`	`SNK_DETACH`	Table 64	R/W	`00h`
`9Ch…9Fh`	Reserved	-	-	-
`A0h…A1h`	`VENDOR_STATUS`	Table 65	R/W1C	`0000h`
`A2h…A3h`	`VENDOR_STATUS_ALERT_MASK`	Table 66	R/W	`0000h`
`A4h…A5h`	`VBUS_FAULT_CTRL`	Table 67	R/W	`0101h`
`A6h`	`VCONN_FAULT_CTRL`	Table 68	R/W	`01h`
`A7h`	Reserved	-	-	-
`A8h…A9h`	`OCP_OUTPUT_CTRL`	Table 69	R/W	`0000h`
`AAh`	`PROCHOT_EN`	Table 70	R/W	`00h`
`ABh…B0h`	Reserved	-	-	-
`B1h`	`Control1`	Table 71	R/W	`0000h`
`B2h...E1h`	Reserved	-	-	-
`E2h...E3h`	`TYPE_C_PARAMETER`	Table 72	R/W	`0190h`
`E4h...FFh`	Reserved	-	-	-

7.2 Register Descriptions

The Address | Reset Value | Access line under each register below is not printed in the datasheet. It is derived from the register map in 7.1 and from the register's own bit table, and is included here as a summary. Where the source prints no single reset word, it is given as "per-bit (see table)". Everything else in this section is transcribed from the printed page.

7.2.1 VENDOR_ID (00h)

Address: 00h...01h | Reset Value: 045Bh | Access: R

Table 8. VENDOR_ID Register

Bits	Field	Access	Default	Description
B15..0	`Vendor ID (VID)`	R	`045Bh`	A Vendor ID, or VID, is used to identify the TCPC vendor. The VID is a unique 16-bit unsigned integer assigned by USB-IF.

7.2.2 PRODUCT_ID (03h) and DEVICE_ID (04h)

Address: 03h (register map: 02h...03h) | Reset Value: 026Dh | Access: R

Table 9. PRODUCT_ID Register

Bits	Field	Access	Default	Description
B15..0	`USB Product ID (PID)`	R	`026Dh`	The Product ID, or PID, is used to identify the product. A unique 16-bit unsigned integer assigned uniquely by the Vendor to identify the TCPC.

`DEVICE_ID` (0x04)

Address: 04h (register map: 04h...05h) | Reset Value: 0100h | Access: R

Table 10. DEVICE_ID Register

Bits	Field	Access	Default	Description
B15..0	`bcdDevice`	R	`0100h`	The Device ID, bcdDevice, is used to identify the product release version. A unique 16-bit unsigned integer assigned by the Vendor to identify the version of the TCPC.

7.2.3 USBTYPEC_REV (06h)

Address: 06h...07h | Reset Value: 0021h | Access: R

Table 11. USBTYPEC_REV Register

Bits	Field	Access	Default	Description
B15..8	`Reserved`	R	`00h`	Set to 0
B7..0	`bcdUSBTYPEC Release`	R	`21h`	`0002 0001` – Release 2.1 This register refers to USB Type-C Cable and Connector Specification Revision, USB Type-C represented by a unique 16-bit unsigned register. The format is packed binary coded decimal.

7.2.4 USBPD_REV_VER (08h)

Address: 08h...09h | Reset Value: 3115h | Access: R

Table 12. USBPD_REV_VER Register

Bits	Field	Access	Default	Description
B15..8	`bcdUSBPD Revision`	R	`31h`	`0011 0001` – Revision 3.1 This register refers to USB PD specification Revision, USB PD represented by a unique 16-bit unsigned integer. The format is packed binary coded decimal.
B7..0	`bcdUSBPD Version`	R	`15h`	`0001 0101` – Version 1.5 This register refers to USB PD specification Version, USB PD represented by a unique 16-bit unsigned integer. The format is packed binary coded decimal.

7.2.5 PD_INTERFACE_REV (0Ah)

Address: 0Ah...0Bh | Reset Value: 2012h | Access: R

Table 13. PD_INTERFACE_REV Register

Bits	Field	Access	Default	Description
B15..8	`bcd USB-PD Inter-Block Specification Revision`	R	`20h`	`0010 0000` – Revision 2.0 The USB-Port Controller Specification Revision register refers to this Specification Revision and Version represented by a unique 16-bit unsigned integer. The format is packed binary coded decimal.
B7..0	`bcd USB-PD Inter-Block Specification Version`	R	`12h`	`0001 0010` – Version 1.2 The USB-Port Controller Specification Version register refers to this Specification Revision and Version represented by a unique 16-bit unsigned integer. The format is packed binary coded decimal. Note: RAA489400 can transfer/receive USB PD EPR protocol with unchunked message. RAA489400 is also capable for 48V EPR voltage monitor function based on version 1.3 specification.

7.2.6 ALERT (10h)

Address: 10h...11h | Reset Value: 0200h | Access: R/W

Table 14. ALERT Register

Bits	Field	Access	Default	Description
B15	`Vendor Defined Alert`	R/W1C	`0b`	`0b`: Cleared `1b`: A vendor defined alert has been detected. Defined in VENDOR_STATUS Register (A0h). This bit can be cleared, regardless of the current status VENDOR_STATUS Register (A0h) of the alert source.
B14	`Alert Extended`	R/W1C	`0b`	`0b`: Cleared `1b`: An extended interrupt event has occurred. See ALERT_EXTENDED (21h).
B13	`Extended Status`	R/W1C	`0b`	`0b`: Cleared `1b`: Extended Status changed
B12	`Reserved`	R	`0b`	Set to zero by sender and ignored by receiver.
B11	`VBUS Sink Disconnect Detected`	R/W1C	`0b`	`0b`: Cleared `1b`: The TCPC in Attached_Snk state has detected a Sink disconnect. This bit is only asserted when `VBUS_SINK_DISCONNECT_THRESHOLD` is set and `POWER_CONTROL.AutoDischargeDisconnect` is set to `1b`.
B10	`Rx Buffer Overflow`	R/W1C	`0b`	`0b`: TCPC Rx buffer is functioning properly `1b`: TCPC Rx buffer has overflowed. Future GoodCRC is not sent. Writing 1 to this register acknowledges the overflow. The overflow is cleared by writing to `ALERT.ReceiveSOP*MessageStatus`
B9	`Fault`	R/W1C	`1b`	`0b`: No fault `1b`: A fault has occurred in

Table 14. ALERT Register (Cont.)

Bits	Field	Access	Default	Description
B8	`VBUS Voltage Alarm Lo`	R/W1C	`0b`	`0b`: Cleared `1b`: A low-voltage alarm has occurred This field maintain assert during a low-voltage alarm has occurred. If TCPM needs to disable VBUS voltage alarm function, TCPM needs to set B5 (Disable Voltage Alarms) to `1b` in POWER_CONTROL (1Ch).
B7	`VBUS Voltage Alarm Hi`	R/W1C	`0b`	`0b`: Cleared `1b`: A high-voltage alarm has occurred This field maintain assert during a high-voltage alarm has occurred. If TCPM needs to disable VBUS voltage alarm function, set B5 (Disable Voltage Alarms) to 1 in POWER_CONTROL (1Ch).
B6	`Transmit SOP* Message Successful`	R/W1C	`0b`	`0b`: Cleared `1b`: Reset or SOP* message transmission successful. GoodCRC response received on SOP* message transmission.
B5	`Transmit SOP* Message Discarded`	R/W1C	`0b`	`0b`: Cleared `1b`: Reset or SOP* message transmission not sent because of an incoming receive message. Transmit SOP* message buffer registers are empty.
B4	`Transmit SOP* Message Failed`	R/W1C	`0b`	`0b`: Cleared `1b`: SOP* message transmission not successful, no GoodCRC response received on SOP* message transmission. Transmit SOP* message buffer registers are empty.
B3	`Received Hard Reset`	R/W1C	`0b`	`0b`: Cleared `1b`: Received Hard Reset message
B2	`Received SOP* Message Status`	R/W1C	`0b`	`0b`: Cleared `1b`: RECEIVE_BUFFER register changed. READABLE_BYTE_COUNT (30h) being set to 0 does not set this bit.
B1	`Power Status`	R/W1C	`0b`	`0b`: Cleared `1b`: Power Status changed
B0	`CC Status`	R/W1C	`0b`	`0b`: Cleared `1b`: CC Status changed TCPC does not assert this bit when Looking4Connection changes state in CC_STATUS (1Dh) when `EnableLooking4ConnectionAlert` is set to TCPC_CONTROL (19h) When TCPM sets `EnableLooking4ConnectionAlert` set to 0 in TCPC_CONTROL (19h), TCPC does not assert this bit when Looking4Connection has changed in CC_STATUS (1Dh). When TCPM sets DRP to 0, CC1 to Open and CC2 to Open in ROLE_CONTROL (1Ah), TCPC does not assert this bit even when CC1 and CC2 status has changed.

7.2.7 ALERT_MASK (12h)

Address: 12h...13h | Reset Value: 6FFFh | Access: R/W

Table 15. ALERT_MASK Register

Bits	Field	Access	Default	Description
B15	`Vendor Defined Alert`	R/W	`0b`	`0b`: Interrupt masked `1b`: Interrupt unmasked
B14	`Alert Extended Interrupt Mask`	R/W	`1b`	`0b`: Interrupt masked `1b`: Interrupt unmasked
B13	`Extended Status Interrupt Mask`	R/W	`1b`	`0b`: Interrupt masked `1b`: Interrupt unmasked
B12	`Reserved`	R	`0b`	Set to zero by sender and ignored by receiver.
B11	`VBUS Sink Disconnect Detected`	R/W	`1b`	`0b`: Interrupt masked `1b`: Interrupt unmasked
B10	`Rx Buffer Overflow`	R/W	`1b`	`0b`: Interrupt masked `1b`: Interrupt unmasked
B9	`Fault`	R/W	`1b`	`0b`: Interrupt masked `1b`: Interrupt unmasked
B8	`VBUS Voltage Alarm Lo`	R/W	`1b`	`0b`: Interrupt masked `1b`: Interrupt unmasked
B7	`VBUS Voltage Alarm Hi`	R/W	`1b`	`0b`: Interrupt masked `1b`: Interrupt unmasked
B6	`Transmit SOP* Message successful Interrupt Mask`	R/W	`1b`	`0b`: Interrupt masked `1b`: Interrupt unmasked
B5	`Transmit SOP* Message discarded Interrupt Mask`	R/W	`1b`	`0b`: Interrupt masked `1b`: Interrupt unmasked
B4	`Transmit SOP* Message failed Interrupt Mask`	R/W	`1b`	`0b`: Interrupt masked `1b`: Interrupt unmasked
B3	`Received Hard Reset Message Status Interrupt Mask`	R/W	`1b`	`0b`: Interrupt masked `1b`: Interrupt unmasked (The Hard Reset should generally not be masked)
B2	`Receive SOP* Message Status Interrupt Mask`	R/W	`1b`	`0b`: Interrupt masked `1b`: Interrupt unmasked
B1	`Power Status Interrupt Mask`	R/W	`1b`	`0b`: Interrupt masked `1b`: Interrupt unmasked
B0	`CC Status Interrupt Mask`	R/W	`1b`	`0b`: Interrupt masked `1b`: Interrupt unmasked

7.2.8 POWER_STATUS_MASK (14h)

Address: 14h | Reset Value: DFh | Access: R/W

Table 16. POWER_STATUS_MASK Register

Bits	Field	Access	Default	Description
B7	`Debug Accessory Connected Status Mask`	R/W	`1b`	`0b`: Interrupt masked `1b`: Interrupt unmasked
B6	`TCPC Initialization Status Mask`	R/W	`1b`	`0b`: Interrupt masked `1b`: Interrupt unmasked
B5	`Sourcing Nondefault Voltage Status Interrupt Mask`	R	`0b`	`0b`: Interrupt masked `1b`: Interrupt unmasked
B4	`Sourcing VBUS Status Interrupt Mask`	R/W	`1b`	`0b`: Interrupt masked `1b`: Interrupt unmasked
B3	`VBUS Detection Status Interrupt Mask`	R/W	`1b`	`0b`: Interrupt masked `1b`: Interrupt unmasked
B2	`VBUS Present Status Interrupt Mask`	R/W	`1b`	`0b`: Interrupt masked `1b`: Interrupt unmasked
B1	`VCONN Present Status Interrupt Mask`	R/W	`1b`	`0b`: Interrupt masked `1b`: Interrupt unmasked
B0	`Sinking VBUS Status Interrupt Mask`	R/W	`1b`	`0b`: Interrupt masked `1b`: Interrupt unmasked

7.2.9 FAULT_STATUS_MASK (15h)

Address: 15h | Reset Value: BFh | Access: R/W

Table 17. FAULT_STATUS_MASK Register[1]

Bits	Field	Access	Default	Description
B7	`AllRegistersResetToDefault`	R/W	`1b`	`0b`: Interrupt masked `1b`: Interrupt unmasked The condition that generates AllRegistersResetToDefault Interrupt also resets this bit; therefore, writing a `0b` to this bit does not mask AllRegistersResetToDefault Interrupt.
B6	`Reserved`	R	`0b`	Set to zero by sender and ignored by receiver.
B5	`Auto Discharge Failed Mask`	R/W	`1b`	`0b`: Interrupt masked `1b`: Interrupt unmasked
B4	`Force Discharge Failed Mask`	R/W	`1b`	`0b`: Interrupt masked `1b`: Interrupt unmasked
B3	`VBUS Overcurrent Protection Fault Interrupt Status Mask`	R/W	`1b`	`0b`: Interrupt masked `1b`: Interrupt unmasked
B2	`VBUS Overvoltage Protection Fault Interrupt Status Mask`	R/W	`1b`	`0b`: Interrupt masked `1b`: Interrupt unmasked
B1	`Vconn Overcurrent Fault Interrupt Status Mask`	R/W	`1b`	`0b`: Interrupt masked `1b`: Interrupt unmasked
B0	`I2C Interface Error Interrupt Status Mask`	R/W	`1b`	`0b`: Interrupt masked `1b`: Interrupt unmasked

VBUS_RVP, VBUS_UVP, VCONN_RVP, VCONN_UVP, VCONN_OVP, and VCONN_OTP are masked in Table 66.

7.2.10 EXTENDED_STATUS_MASK (16h)

Address: 16h | Reset Value: 01h | Access: R/W (per bit)

Table 18. EXTENDED_STATUS_MASK Register

Bits	Field	Access	Default	Description
B7..1	`Reserved`	R	`0000000b`	Set to zero by sender and ignored by receiver.
B0	`vSafe0V Status Mask`	R/W	`1b`	0b: Interrupt masked 1b: Interrupt unmasked

7.2.11 ALERT_EXTENDED_MASK (17h)

Address: 17h | Reset Value: 01h | Access: R/W (per bit)

Table 19. ALERT_EXTENDED_MASK Register

Bits	Field	Access	Default	Description
B7...1	`Reserved`	R	`00000b`	Set to zero by sender and ignored by receiver.
B0	`Sink Fast Role Swap Mask`	R/W	`1b`	0b: Interrupt masked 1b: Interrupt unmasked

7.2.12 TCPC_CONTROL (19h)

Address: 19h | Reset Value: 00h | Access: R/W (per bit)

Table 20. TCPC_CONTROL Register

Bits	Field	Access	Default	Description
B7	`Enable SMBus PEC`	R	`0b`	0b: SMBus PEC is disabled (default)
B6	`Enable Looking4Connection Alert`	R/W	`0b`	0b: Disable ALERT.CCStatus assertion when CC_STATUS.Looking4Connection changes (default) 1b: Enable ALERT.CCStatus assertion when CC_STATUS.Looking4Connection changes
B5	`Reserved`	R	`0b`	Set to zero by sender and ignored by receiver.
B4	`Debug Accessory Control`	R/W	`0b`	0b: Controlled by TCPC (power on default) 1b: Controlled by TCPM. This bit no effect to any function, always it controlled by TCPC.
B3..2	`I2C Clock Stretching Control`	R	`00b`	Clock Stretching Control 00b: Disable clock stretching. TCPC does not perform any clock stretching during I²C transfers.

Table 20. TCPC_CONTROL Register (Cont.)

Bits	Field	Access	Default	Description
B1	`BIST Test Mode`	R/W	`0b`	Setting this bit to 1 is intended to be used only when a USB compliance tester is using USB BIST Test Data to test the PHY layer of the TCPC. The TCPM should clear this bit when a disconnect is detected. 0: Normal Operation. Incoming messages enabled by `RECEIVE_DETECT (2Fh)` passed to TCPM via Alert. 1: BIST Test Mode. Incoming messages enabled by `RECEIVE_DETECT (2Fh)` result in GoodCRC response but might not be passed to the TCPM through Alert. TCPC does not result in a Receive SOP* Message Status or a Rx Buffer Overflow alert.
B0	`Plug Orientation`	R/W	`0b`	0b: When VCONN is enabled, apply it to the CC2 pin. Monitor the CC1 pin for BMC communications if PD messaging is enabled. 1b: When VCONN is enabled, apply it to the CC1 pin. Monitor the CC2 pin for BMC communications if PD messaging is enabled. TCPM needs to set this bit to oriented position. If TCPM does not set this bit to oriented position, TCPC cannot transmit and receive any messages.

7.2.13 ROLE_CONTROL (1Ah)

Address: 1Ah | Reset Value: depends on power-up source (see CC2/CC1 bits) | Access: R/W (per bit)

Table 21. ROLE_CONTROL Register

Bits	Field	Access	Default	Description
B7	`Reserved`	R	`0b`	Set to zero by sender and ignored by receiver.
B6	`DRP`	R/W	`0b`	0b: No DRP. Bits B3..0 determine Rp/Rd/Ra or open settings 1b: DRP. The TCPC uses the Rp value defined in B5..4 when a connection is resolved, that is upon entry to Potential_Connect_as_Src in Figure 4-19 of TCPCI specification. The TCPC toggles CC1 & CC2 after receiving COMMAND.Look4Connection and until a connection is detected. Upon connection, TCPC resolves to either an Rp or Rd and report the CC1/CC2 State in `CC_STATUS` Register The CC pins stay in Potential_Connect_as_Src or Potential_Connect_as_Sink until directed otherwise.
B5..4	`Rp Value`	R/W	`00b`	00b: Rp default 01b: Rp 1.5A 10b: Rp 3.0A 11b: Reserved When TCPC connects works as VBUS source, this field can be updated.
B3..2	`CC2`	R/W	`10b` or `11b`	00b: Not supported 01b: Rp (Use Rp definition in B5..4) 10b: Rd 11b: Open (Disconnect or don't care) If TCPM sets this fields to 00b, it is not effect for CC2. TCPM needs to set this bit based on TCPCI specification. In connected case, TCPC controls CC lines by USB Type-C State. TCPM needs to control USB Type-C state machine correctly, for example, power role swap, error recovery, or others When the TCPC is powered up by VBUS, the reset value of this bit is 10b. When the TCPC is powered up by VSYS33, the reset value of this bit is 11b.
B1..0	`CC1`	R/W	`10b` or `11b`	00b: Not supported 01b: Rp (Use Rp definition in B5..4) 10b: Rd 11b: Open (Disconnect or don't care) If TCPM sets this fields to 00b, it is not effect for CC1. When the TCPC is powered up by VBUS, the reset value of this bit is 10b. When the TCPC is powered up by VSYS33, the reset value of this bit is 11b.

7.2.14 FAULT_CONTROL (1Bh)

Address: 1Bh | Reset Value: 00h | Access: R/W (per bit)

Table 22. FAULT_CONTROL Register^[1]

Bits	Field	Access	Default	Description
B7..4	`Reserved`	R	`0000b`	Set to zero by sender and ignored by receiver.
B3	`VBUS Discharge Fault Detection Timer`	R/W	`0b`	0b: VBUS Discharge Fault Detection Timer enabled 1b: VBUS Discharge Fault Detection Timer disabled This enables the timers for both FAULT_STATUTS.AutoDischargeFailed and FAULT_STATUS.ForceDischargeFailed
B2	`VBUS Overcurrent Protection Fault`	R/W	`0b`	0b: Internal OCP circuit enabled 1b: Internal OCP circuit disabled If OCP occurs when this bit is set to 0b, RAA489400 turns off VBUS gate and sets `FAULT_STATUS` Register. See VBUS Overcurrent Protection for more information.
B1	`VBUS Overvoltage Protection Fault`	R/W	`0b`	0b: Internal OVP circuit enabled 1b: Internal OVP circuit disabled If OVP occurs when this bit is set to 0b, RAA489400 turns off VBUS gate and sets `FAULT_STATUS (1Fh)`. See VBUS Overvoltage Protection for more information.
B0	`VCONN Overcurrent Fault`	R/W	`0b`	0b: Fault detection circuit enabled 1b: Fault detection circuit disabled If VCONN OCP occurs when this bit is set to 0b, RAA489400 turns off VCONN Mux and sets `FAULT_STATUS` Register. See VCONN Overcurrent Protection for more information. Regardless of this setting, if RAA489400 detects VCONN overcurrent, RAA489400 turns off VCONN Mux.

VBUS_RVP and VBUS_UVP are controlled in Table 67. VCONN_OTP is controlled in Table 68.

7.2.15 POWER_CONTROL (1Ch)

Address: 1Ch | Reset Value: 62h | Access: R/W (per bit)

Table 23. POWER_CONTROL Register

Bits	Field	Access	Default	Description
B7	`Fast Role Swap Enable`	R/W	`0b`	0b: Disable Fast Role Swap function 1b: Enable Fast Role Swap function Note: When this bit is set to 1b, VSRC_CP_EN is required to set to 1b in `VBUS_CP_CTRL` Register
B6	`VBUS_VOLTAGE Monitor`	R/W	`1b`	0b: VBUS_VOLTAGE Monitoring is enabled 1b: VBUS_VOLTAGE Monitoring is disabled (default) Controls only VBUS_VOLTAGE Monitoring function. `VBUS_VOLTAGE (70h)` reports all zeroes if disabled.
B5	`Disable Voltage Alarms`	R/W	`1b`	0b: Voltage Alarms Power status reporting is enabled 1b: Voltage Alarms Power status reporting is disabled (default) Controls `VBUS_VOLTAGE_ALARM_HI_CFG (76h)` and `VBUS_VOLTAGE_ALARM_LO_CFG (78h)`.
B4	`Auto Discharge Disconnect`	R/W	`0b`	0b: The TCPC does not automatically discharge VBUS based on VBUS voltage (default) 1b: The TCPC automatically discharges. Setting this bit in a Source TCPC triggers the following actions upon a disconnect detection: 1. Disable sourcing power over VBUS 2. VBUS discharge Sourcing power over VBUS is disabled before or at the same time as starting VBUS discharge. Setting this bit in a Sink TCPC triggers the following action upon a disconnect detection: 1. VBUS discharge The TCPC automatically disables discharge (without clearing this bit) once the voltage on VBUS is below vSafe0V (max). TCPC does not re-apply discharge circuit if VBUS rises above vSafe0V.
B3	`Enable Bleed Discharge`	R/W	`0b`	0b: Disable bleed discharge of VBUS (default) 1b: Enable bleed discharge of VBUS
B2	`Force Discharge`	R/W	`0b`	0b: Disable forced discharge (default) 1b: Enable forced discharge of VBUS. Refer to Section 4.4.5.4.3 in TCPCI specification for more detail.
B1	`VCONN Power Supported`	R	`1b`	0b: Deliver at least 1W on VCONN 1b: Deliver at least the power indicated in DEVICE_CAPABILITIES.VCONNPowerSupported. VCONN OCP settings are provided in `VCONN_FAULT_CTRL` Register (`A6h`). 00 = 400mA 01 = 600mA 10 = 800mA 11 = Reserved
B0	`Enable VCONN`	R/W	`0b`	0b: Disable VCONN Source (default) 1b: Enable VCONN Source to CC

7.2.16 CC_STATUS (1Dh)

Address: 1Dh | Reset Value: 00h | Access: R

Table 24. CC_STATUS Register

Bits	Field	Access	Default	Description
B7..6	`Reserved`	R	`00b`	Set to zero by sender and ignored by receiver
B5	`Looking4Connection`	R	`0b`	0b: TCPC is not actively looking for a connection. A transition from '1' to '0' indicates a potential connection has been found. 1b: TCPC is looking for a connection (toggling as a DRP or looking for a connection as Sink/Source only condition)
B4	`ConnectResult`	R	`0b`	0b: the TCPC is presenting Rp 1b: the TCPC is presenting Rd TCPC updates this bit when Looking4Connection change to 0 from 1.
B3..2	`CC2 State`	R	`00b`	If (ROLE_CONTROL.CC2 = Rp) or (ConnectResult = 0) 00b: SRC.Open (Open, Rp) 01b: SRC.Ra (below maximum vRa) 10b: SRC.Rd (within the vRd range) 11b: Reserved If (ROLE_CONTROL.CC2 = Rd) or (ConnectResult = 1) 00b: SNK.Open (Below maximum vRa) 01b: SNK.Default (Above minimum vRd-Connect) 10b: SNK.Power1.5 (Above minimum vRd-Connect) Detects Rp 1.5A 11b: SNK.Power3.0 (Above minimum vRd-Connect) Detects Rp 3.0A If ROLE_CONTROL.CC2 = Ra, this field is set to 00b If ROLE_CONTROL.CC2 = Open, this field is set to 00b This field always returns 00b if (Looking4Connection = 1) or (POWER_CONTROL.EnableVconn = 1 and TCPC_CONTROL.PlugOrientation=0). Otherwise, the returned value depends upon ROLE_CONTROL.CC2.

Table 24. CC_STATUS Register (Cont.)

Bits	Field	Access	Default	Description
B1..0	`CC1 State`	R	`00b`	If (ROLE_CONTROL.CC1 = Rp) or (ConnectResult=0) 00b: SRC.Open (Open, Rp) 01b: SRC.Ra (below maximum vRa) 10b: SRC.Rd (within the vRd range) 11b: Reserved If (ROLE_CONTROL.CC1 = Rd) or ConnectResult = 1) 00b: SNK.Open (Below maximum vRa) 01b: SNK.Default (Above minimum vRd-Connect) 10b: SNK.Power1.5 (Above minimum vRd-Connect) Detects Rp-1.5A 11b: SNK.Power3.0 (Above minimum vRd-Connect) Detects Rp-3.0A If ROLE_CONTROL.CC1=Ra, this field is set to 00b If ROLE_CONTROL.CC1=Open, this field is set to 00b This field always returns 00b if (Looking4Connection = 1) or (POWER_CONTROL.EnableVconn = 1 and TCPC_CONTROL.PlugOrientation = 1). Otherwise, the returned value depends upon ROLE_CONTROL.CC1.

7.2.17 POWER_STATUS (1Eh)

Address: 1Eh | Reset Value: 48h | Access: R

Table 25. POWER_STATUS Register

Bits	Field	Access	Default	Description
B7	`Debug Accessory Connected`	R	`0b`	0b: No Debug Accessory connected (default) 1b: Debug Accessory connected TCPC asserts this bit when it transitions to Debug Accessory state. If TCPC detects disconnected, this bit is de-asserted. TCPC detects Rd and Rd or Rp and Rp on Apply State. If the TCPC detects DebugAccessory device with tCCDebounce, it transitions to DebugAccessory.SRC or SNK.
B6	`TCPC Initialization Status`	R	`1b`	0b: The TCPC has completed initialization and all registers are valid 1b: The TCPC is still performing internal initialization and the only registers that are guaranteed to return the correct values are `00h`...`0Fh` TCPC clears this field and asserts ALERT.POWER_STATUS after TCPC completes initialization of VBUS detection and the first VBUS detection.
B5	`Sourcing Nondefault Voltage`	R	`0b`	0b: vSafe5V (Fixed).
B4	`Sourcing VBUS`	R	`0b`	0b: Sourcing VBUS is disabled 1b: Sourcing VBUS is enabled This bit does not control the path, just provides a monitor of the status. RAA489400 controls this bit with based on a command and an event (for example, disconnection, and FRS) and indicates that Sourcing VBUS is in progress.
B3	`VBUS Detection Enabled`	R	`1b`	0b: VBUS Detection Disabled 1b: VBUS Detection Enabled (default) Indicates whether the TCPC is monitoring for VBUS Present and vSafe0V level. After Power-on reset, VBUS detection is enabled automatically.
B2	`VBUS Present`	R	`0b`	0b: VBUS Disconnected 1b: VBUS Connected TCPC asserts VBUS_present when TCPC detects VBUS rises above VBUS_OK_r for more than 1ms. TCPC de-asserts VBUS_present when TCPC detects VBUS falls below VBUS_OK-r – VBUS_OK_h for more than 10µs. In Sink mode, deasserting this bit does not mean Sink Disconnect. Deasserting this bit is independent from VBUS Sink Disconnect which is detected when VBUS voltage is below VBUS_SINK_DISCONNECT_THRESHOLD register.
B1	`VCONN Present`	R	`0b`	0b: VCONN is not present 1b: This bit is asserted when VCONN present CC1 or CC2. Threshold is fixed at 2.4V TCPC de-asserts this bit when TCPC detects VBUS falls below 2.4V. When EnableVCONN is disabled in `POWER_CONTROL (1Ch)`, this bit indicates 0b.
B0	`Sinking VBUS`	R	`0b`	0b: Sink is Disconnected 1b: TCPC is sinking VBUS to the system load RAA489400 controls this bit with based on a command and an event (for example, disconnect or FRS) and indicates that Sinking VBUS is in progress.

7.2.18 `FAULT_STATUS` (`0x1F`)

Address: 1Fh | Reset Value: per-bit (see table) | Access: R/W1C (Reserved bits: R)

Table 26. FAULT_STATUS Register

Bits	Field	Access	Default	Description
B7	`AllRegistersResetToDefault`	R/W1C	`1b`	This bit is asserted when the TCPC resets all registers to their default value. This happens at initial power up or if an unexpected power reset occurs.
B6	`Reserved`	R	`0b`	Set to zero by sender and ignored by receiver
B5	`Auto Discharge Failed`	R/W1C	`0b`	`0b`: No discharge failure `1b`: Discharge commanded by the TCPM failed If `POWER_CONTROL.AutoDischargeDisconnect` is set, the TCPC reports discharge fails if VBUS is not below vSafe0V within tSafe0V.
B4	`Force Discharge Failed`	R/W1C	`0b`	`0b`: No discharge failure `1b`: Discharge commanded by the TCPM failed If `POWER_CONTROL.ForceDischarge` is set, the TCPC reports a discharge fails if VBUS is not below vSafe0V within tSafe0V.
B3	`VBUS Overcurrent Protection Fault`	R/W1C	`0b`	`0b`: Not in an overcurrent protection state `1b`: Overcurrent fault latched If VBUS current exceeds VBUS_OC setting in. See VBUS Overcurrent Protection for more information. This bit remains `1b` even if TCPM writes `1b` to this bit when VBUS Overcurrent condition still occurs.
B2	`VBUS Overvoltage Protection Fault`	R/W1C	`0b`	`0b`: Not in an overvoltage protection state `1b`: Overvoltage fault latched. See VBUS Overvoltage Protection for more information. This bit remains `1b` even if TCPM writes `1b` to this bit when VBUS Overvoltage condition still occurs.
B1	`VCONN Overcurrent Fault`	R/W1C	`0b`	`0b`: No Fault detected `1b`: Overcurrent VCONN fault latched. This bit remains `1b` even if TCPM writes `1b` to this bit when VCONN Overcurrent condition still occurs.
B0	`I2C Interface Error`	R/W1C	`0b`	`0b`: No Error `1b`: I²C error has occurred. When the following conditions occur, this bit is asserted TCPM writes to the `TRANSMIT` register that is not HardReset, CableReset or BIST Carrier Mode 2 when the `TRANSMIT_BUFFER` is empty has less than 2 bytes `I2C_WRITE_BYTE_COUNT` is different than the number of bytes written in the `TRANSMIT_BUFFER`. Main State-Machine has entered Connected_Invalid state TCPM writes an invalid COMMAND DisableVbusDetect command when TCPC sourcing or sinking power over VBUS. SinkVbus command when TCPC is sourcing power over VBUS. SourceVbusDefaultVoltage command when TCPC sinking power over VBUS. SourceVbusNondefaultVoltage command SendFRSwapSignal command Value written to `COMMAND` register is not defined in the TCPCI spec.

Note: VBUS_RVP, VBUS_UVP, VCONN_RVP, VCONN_UVP, VCONN_OVP, and VCONN_OTP are reported in Table 65.

7.2.19 `EXTENDED_STATUS` (`0x20`)

Address: 20h | Reset Value: per-bit (see table) | Access: R

Table 27. EXTENDED_STATUS Register

Bits	Field	Access	Default	Description
B7..1	`Reserved`	R	`0000000b`	Set to zero by sender and ignored by receiver
B0	`vSafe0V`	R	`1b`	`0b`: VBUS is not at vSafe0V `1b`: VBUS is at vSafe0V TCPC reports VBUS is at vSafe0V when TCPC detects VBUS is below 0.8V. This bit is not valid when `VbusDetectionEnabled` = `0b` in `POWER_STATUS` (`1Eh`)

7.2.20 `ALERT_EXTENDED` (`0x21`)

Address: 21h | Reset Value: per-bit (see table) | Access: R/W1C (Reserved bits: R)

Table 28. ALERT_EXTENDED Register

Bits	Field	Access	Default	Description
B7..1	`Reserved`	R	`00000000b`	Set to zero by sender and ignored by receiver
B0	`Sink Fast Role Swap`	R/W1C	`0b`	`0b`: No Fast Role Swap signal received `1b`: Fast Role Swap signal received When `FRS_EN` is set to `1b` in `PROCHOT_EN` register and this bit is set to one, PROCHOT# is asserted Writing one to this bit clears the bit to zero. If bit 0 of this register and bit 1 of `Vendor_STATUS` register are zero, PROCHOT# is deasserted (Hi-Z).

7.2.21 `COMMAND` (`0x23`)

Address: 23h | Reset Value: per-bit (see table) | Access: W

Table 29. COMMAND Register

Bits	Field	Access	Default	Description
B7..0	`Command`	W	`00h`	Refer to Table 30.

Table 30. COMMAND Register Setting

Register Setting	Description
`0001 0001b`	WakeI2C (no action is taken other than to wake the I²C interface).
`0010 0010b`	DisableVbusDetect. Disable VBUS present and vSafe0V detection. The TCPC ignores this command and assert the `FAULT_STATUS.I2CInterfaceError` if it has sourcing or sinking power over VBUS enabled. If the TCPC received this command validly, TCPC clear the `POWER_STATUS.VBUS Detection Enable`.
`0011 0011b`	EnableVbusDetect. Enable VBUS present and vSafe0V detection. If TCPC received this command, TCPC sets `POWER_STATUS.VBUS Detection Enable` after update VBUS present and vSafe0V to latest status and it can notify the ALERT for `POWER_STATUS.VBUS_present` and `EXTENDED_STATUS.vSafe0V`.

Table 30. COMMAND Register Setting (Cont.)

Register Setting	Description
`0100 0100b`	DisableSinkVbus. Disable sinking power over VBUS but does not discharge VBUS to vSafe0V. If VBUS has not been discharged at Sink detach, for example, Auto Disconnect Discharge is set to `0b`, TCPM needs to use Force Discharge in addition to the DisableSinkVbus command. This COMMAND does not disable `POWER_STATUS.VBUSPresent` detection. The TCPC clears `FAULT_STATUS.InternalorExternalOCP`, `FAULT_STATUS.InternalorExternalOVP`, and `VENDOR_STATUS` register except Bit9.VCONN_0p8V, Bit5.FAULT_STATE, Bit15.Sink path discharge timeout, and Bit14. Sink path discharge complete (B14). The TCPC turn off VBus Sink path gate (Nch-MOSFET with VSNK_GATE or external component with GPIO (Sink Enable function).
`0101 0101b`	SinkVbus. Enable sinking power over VBUS and enable VBus present detection. The TCPC ignores this command and assert the `FAULT_STATUS.I2CInterfaceError` if it has sourcing power over Vbus enabled. The TCPC turn on VBus Sink path gate (Nch-MOSFET with VSNK_GATE or external component with GPIO (Sink Enable function) and stop VBUS discharge. If TCPC received this command, TCPC completes setting charging and loading of VBUS. When TCPC detects VBUS removed, TCPC controls a discharge circuit If TCPM has set `POWER_CONTROL.Auto Discharge Disconnect` to 1. Also, when TCPC detects SNK.Open specified in `SNK_DETACH` register, TCPC controls a discharge circuit If TCPM has set `SNK_DETACH.AUTO_DISCHG_SNK_OPEN` to 1. So TCPM does not require to write a `COMMAND.DisableSinkVbus` when TCPC has detect remover the VBUS.
`0110 0110b`	DisableSourceVbus. Disable sourcing power over VBUS. The TCPC clears `FAULT_STATUS.InternalorExternalOCP`, `FAULT_STATUS.InternalorExternalOVP`, and `VENDOR_STATUS` register except Bit9.VCONN_0p8V, Bit5.FAULT_STATE, Bit15.Sink path discharge timeout and Bit14.Sink path discharge complete (B14). This COMMAND does not disable `POWER_STATUS.VBUSPresent` detection. The TCPC turns off VBus Source path gate (Nch-MOSFET with VSRC_GATE or external component with GPIO (Source Enable function) and discharges VBUS voltage to vSafe0V.
`0111 0111b`	SourceVbusDefaultVoltage. Enable sourcing vSafe5V over VBUS and enable VBus present detection. Source transitions to vSafe5V if at a high voltage. The TCPC ignores this command and assert the `FAULT_STATUS.I2CInterfaceError` if it has sinking power over Vbus enabled. The TCPC turns on the VBus Source path gate (Nch-MOSFET with VSRC_GATE) or external component with GPIO (Source Enable function) and stops VBUS discharge.
`1000 1000b`	SourceVbusNondefaultVoltage. RAA489400 does not support this command. When RAA489400 receives this command, this command is ignored and the `FAULT_STATUS.I2CInterfaceError` is set to `1b`.
`1001 1001b`	Look4Connection. Start DRP Toggling if `ROLE_CONTROL.DRP` = `1b`. If `ROLE_CONTROL.CC1/CC2` = `01b` start with Rp, if `ROLE_CONTROL.CC1/CC2` = `10b` start with Rd. If `ROLE_CONTROL.CC1/CC2` are not both `01b` or `10b`, then do not start toggling. The TCPM issues `COMMAND.Look4Connection` to enable the TCPC to restart Connection Detection in cases where the `ROLE_CONTROL` contents do not change. An example of this is when a potential connection as a Source occurred but was further debounced by the TCPM to find the Sink disconnected. In this case a Source Only or DRP should go back to its Unattached.Src state. This would result in `ROLE_CONTROL` staying the same.

Table 30. COMMAND Register Setting (Cont.)

Register Setting	Description
`1010 1010b`	RxOneMore. Configure the receiver to automatically clear the `RECEIVE_DETECT` (`2Fh`) after sending the next GoodCRC. This is used to shutdown reception of packets at a known point regardless of packet separation or the depth of the receive FIFO in the TCPC.
`1100 1100b`	SendFRSwapSignal. RAA489400 does not support this command. When RAA489400 receives this command, this command is ignored and the `FAULT_STATUS.I2CInterfaceError` is set to `1b`.
`1101 1101b`	ResetTransmitBuffer. The TCPC resets the pointer of the `TRANSMIT_BUFFER` register to offset 1 and the contents of `TRANSMIT_BUFFER` becomes invalid when this command is issued by the TCPM. This command is supported by TCPC compliant with USB Port Controller Specification Revision 2.0.
`1110 1110b`	ResetReceiveBuffer. The TCPC resets the pointer of `RX_BUFFER` when this command is issued by the TCPM. TCPC does not clear the content of the buffer upon receiving this command. The TCPM issues this command in order to re-read the `RECEIVE_BUFFER.RX_BUF_BYTE_x`. This command is supported by TCPC compliant with USB Port Controller Specification Revision 2.0.
`1111 1111b`	I2C Idle RAA489400 does not support. No action is taken.

7.2.22 `DEVICE_CAPABILITIES_1` (`0x24`)

Address: 24h | Reset Value: per-bit (see table) | Access: R

Table 31. DEVICE_CAPABILITIES_1 Register

Bits	Field	Access	Default	Description
B15	`VBUS Nondefault Target`	R	`0b`	`0b`: `VBUS_NONDEFAULT_TARGET` register not implemented `1b`: `VBUS_NONDEFAULT_TARGET` register implemented
B14	`VBUS OCP Reporting`	R	`1b`	`0b`: VBUS OCP is not reported by the TCPC `1b`: VBUS OCP is reported by the TCPC
B13	`VBUS OVP Reporting`	R	`1b`	`0b`: VBUS OVP is not reported by the TCPC `1b`: VBUS OVP is reported by the TCPC
B12	`Bleed Discharge`	R	`1b`	`0b`: No Bleed Discharge implemented in TCPC `1b`: Bleed Discharge is implemented in the TCPC
B11	`Force Discharge`	R	`1b`	`0b`: No Force Discharge implemented in TCPC `1b`: Force Discharge is implemented in the TCPC
B10	`VBUS Measurement and Alarm Capable`	R	`1b`	`0b`: No VBUS voltage measurement nor VBUS Alarms `1b`; VBUS voltage measurement and VBUS Alarms
B9..8	`Source Resistor Supported`	R	`10b`	`00b`: Rp default only `01b`: Rp 1.5A and default `10b`: Rp 3.0A, 1.5A, and default `11b`: Reserved Rp values which can be configured by the TCPM with `ROLE_CONTROL` (`1Ah`)
B7..5	`Power Roles Supported`	R	`110b`	`000b`: USB Type-C Port Manager can configure the Port as Source only or Sink only (not DRP) `001b`: Source only `010b`: Sink only `011b`: Sink with accessory support `100b`: DRP only `101b`: Source, Sink, DRP, Adapter/Cable all supported `110b`: Source, Sink, DRP `111b`: Not valid

Table 31. DEVICE_CAPABILITIES_1 Register (Cont.)

Bits	Field	Access	Default	Description
B4	`SOP’_DBG/SOP”_DBG Support`	R	`1b`	`0b`: All SOP* except SOP’_DBG/SOP”_DBG `1b`: All SOP* messages are supported Configured in `RECEIVE_DETECT` (`2Fh`) and `TRANSMIT` (`50h`).
B3	`Source VCONN`	R	`1b`	`0b`: TCPC is not capable of switching the VCONN Source `1b`: TCPC is capable of switching the VCONN Source
B2	`Sink VBUS`	R	`1b`	`0b`: TCPC is not capable controlling the sink path to the system load `1b`: TCPC is capable of controlling the sink path to the system load
B1	`Source Nondefault VBUS`	R	`0b`	`0b`: TCPC is not capable of sourcing nondefault voltages over VBUS `1b`: TCPC is capable of sourcing nondefault voltages over VBUS
B0	`Source VBUS`	R	`1b`	`0b`: TCPC is not capable of controlling the source path to VBUS `1b`: TCPC is capable of controlling the source path to VBUS

7.2.23 `DEVICE_CAPABILITIES_2` (`0x26`)

Address: 26h | Reset Value: per-bit (see table) | Access: R

Table 32. DEVICE_CAPABILITIES_2 Register

Bits	Field	Access	Default	Description
B15	`DEVICE_CAPABILITIES_3 Support`	R	`1b`	`0b`: TCPC does not support the `DEVICE_CAPABILITIES_3` register. `1b`: TCPC supports the `DEVICE_CAPABILITIES_3` register.
B14	`Message Disable Disconnect`	R	`1b`	`0b`: Sink TCPC disables PD message delivery when `ALERT.VbusinkDisconnectDetected` has been asserted `1b`: Sink TCPC disables PD message delivery using the condition as defined in `RECEIVE_DETECT.MessageDisableDisconnect`
B13	`Generic Timer`	R	`0b`	`0b`: `GENERIC_TIMER` register is not supported `1b`: `GENERIC_TIMER` register is supported
B12	`Long Message`	R	`0b`	`0b`: RAA489400 does not support long message but RAA489400 can transfer and receive EPR protocol as unchunked message
B11	`SMBus PEC`	R	`0b`	`0b`: `TCPC_CONTROL.EnableSMBusPEC` not implemented `1b`: `TCPC_CONTROL.EnableSMBusPEC` implemented
B10	`Source FR Swap`	R	`0b`	`0b`: Not capable of sending Fast Role Swap signal as Source when receiving `COMMAND.SendFRSwapSignal`. `1b`: Capable of sending Fast Role Swap signal as Source TCPC when receiving `COMMAND.SendFRSwapSignal`.
B9	`Sink FR Swap`	R	`1b`	`0b`: `POWER_CONTROL.FastRoleSwapEnable` not supported as Sink `1b`: `POWER_CONTROL.FastRoleSwapEnable` supported as Sink
B8	`Watchdog Timer`	R	`0b`	`0b`: `TCPC_CONTROL.EnableWatchdogTimer` not implemented `1b`: `TCPC_CONTROL.EnableWatchdogTimer` implemented

Table 32. DEVICE_CAPABILITIES_2 Register (Cont.)

Bits	Field	Access	Default	Description
B7	`Sink Disconnect Detection`	R	`1b`	`0b`: `VBUS_SINK_DISCONNECT_THRESHOLD` not implemented, use `POWER_STATUS.VbusPresent`=`0b` to indicate a Sink disconnect. `1b`: `VBUS_SINK_DISCONNECT_THRESHOLD` implemented, VBUS falling below `VBUS_SINK_DISCONNECT_THRESHOLD` is used as indication of Sink disconnect.
B6	`Stop Discharge Threshold`	R	`1b`	`0b`: `VBUS_STOP_DISCHARGE_THRESHOLD` not implemented `1b`: `VBUS_STOP_DISCHARGE_THRESHOLD` implemented
B5..4	`VBUS Voltage Alarm LSB`	R	`00b`	The TCPC might ignore the number of Least Significant Bits (LSBs) of 4 Threshold and Alarm registers as denoted in this field. Whether or not the TCPC ignores these might be dependent on the instantaneous Voltage of VBus. The TCPM can use this information to round up or down the affected registers as appropriate. The registers affected are: `VBUS_SINK_DISCONNECT_THRESHOLD`, `VBUS_STOP_DISCHARGE_THRESHOLD`, `VBUS_VOLTAGE_ALARM_HI_CFG`, and `VBUS_VOLTAGE_ALARM_LO_CFG`. `00`: TCPC always has 25mV LSB for its voltage alarms and thresholds and uses all bits defined. `01`: TCPC might have 50mV LSB for its voltage alarm and might ignore the least significant bit. `10`: TCPC might have 100mV LSB for its voltage alarm and might ignore the two least significant bits. `11`: Reserved This field is ignored if `VBUS_VOLTAGE_ALARM_LO_CFG` and `VBUS_VOLTAGE_ALARM_HI` are not supported.
B3..1	`VCONN Power Supported`	R	`001b`	`000b`: 1.0W `001b`: 1.5W `010b`: 2.0W `011b`: 3W `100b`: 4W `101b`: 5W `110b`: 6W `111b`: External
B0	`VCONN Overcurrent Fault Capable`	R	`1b`	`0b`: TCPC is not capable of detecting a VCONN overcurrent fault `1b`: TCPC is capable of detecting a VCONN overcurrent fault

7.2.24 `STANDARD_INPUT_CAPABILITIES` (`0x28`)

Address: 28h | Reset Value: per-bit (see table) | Access: R

Table 33. STANDARD_INPUT_CAPABILITIES Register

Bits	Field	Access	Default	Description
B7..5	`Reserved`	R	`000b`	Set to zero by sender and ignored by receiver
B4..3	`Source Fast Role Swap`	R	`00b`	`00b`: Not present in TCPC `01b`: Present in TCPC as an input only pin `10b`: Present in TCPC as a bidirectional pin, sharing with the STANDARD OUTPUT SIGNAL VBUS Sink Disconnect Detect Indicator. `11b`: Reserved
B2	`VBUS External Overvoltage Fault`	R	`0b`	`0b`: Not present in TCPC `1b`: Present in TCPC
B1	`VBUS External Overcurrent Fault`	R	`1b`	`0b`: Not present in TCPC `1b`: Present in TCPC `GPIO1/2/3/4_CTRL`, `VBUS_PATH_CTRL`, `VBUS_GPIO_CTRL`, and `GPIO_OC_EN` register need to be set to enable.
B0	`Force Off VBUS (Source or Sink)`	R	`0b`	`0b`: Not present in TCPC `1b`: Present in TCPC

7.2.25 `STANDARD_OUTPUT_CAPABILITIES` (`0x29`)

Address: 29h | Reset Value: per-bit (see table) | Access: R

Table 34. STANDARD_OUTPUT_CAPABILITIES Register

Bits	Field	Access	Default	Description
B7	`VBUS Sink Disconnect Detect Indicator`	R	`0b`	`0b`: Not present in TCPC `1b`: Present in TCPC
B6	`Debug Accessory Indicator`	R	`0b`	`0b`: Not present in TCPC `1b`: Present in TCPC RAA489400 does not support Debug Accessory Indicator output pin function. RAA489400 supports Debug Accessory connection status.
B5	`VBUS Present Monitor`	R	`0b`	`0b`: Not present in TCPC `1b`: Present in TCPC
B4	`Audio Adapter Accessory Indicator`	R	`0b`	`0b`: Not present in TCPC `1b`: Present in TCPC
B3	`Active Cable Indicator`	R	`0b`	`0b`: Not present in TCPC `1b`: Present in TCPC
B2	`MUX Configuration Control`	R	`0b`	`0b`: Not present in TCPC `1b`: Present in TCPC
B1	`Connection Present`	R	`0b`	`0b`: No Connection `1b`: Connection Controlled by the TCPM.
B0	`Connector Orientation`	R	`0b`	`0b`: Not present in TCPC `1b`: Present in TCPC

7.2.26 `MESSAGE_HEADER_INFO` (`0x2E`)

Address: 2Eh | Reset Value: per-bit (see table) | Access: R/W (Reserved bits: R)

Table 35. MESSAGE_HEADER_INFO Register

Bits	Field	Access	Default	Description
B7..5	`Reserved`	R	`000b`	Set to zero by sender and ignored by receiver.
B4	`Cable Plug`	R/W	`0b`	`0b`: Message originated from Source, Sink, or DRP `1b`: Message originated from a Cable Plug
B3	`Data Role`	R/W	`0b`	`0b`: UFP `1b`: DFP
B2..1	`USB PD Specification Revision`	R/W	`10b`	`00b`: Revision 1.0 `01b`: Revision 2.0 `10b`: Revision 3.0 `11b`: Reserved
B0	`Power Role`	R/W	`0b`	`0b`: Sink `1b`: Source

7.2.27 `RECEIVE_DETECT` (`0x2F`)

Address: 2Fh | Reset Value: per-bit (see table) | Access: R/W

Table 36. RECEIVE_DETECT Register

Bits	Field	Access	Default	Description
B7	`Message Disable Disconnect`	R/W	`0b`	`0b`: Sink TCPC disables PD message delivery when Auto Discharge Disconnect is set in POWER CONTROL register and VBUS voltage falls below VBUS SINK DISCONNECT THRESHOLD register, that is VBUS Sink disconnect is detected (default) TCPM needs to set `0b` in this bit. Regardless of the setting of this bit, Source TCPC always uses SRC.Open as an indication of disconnect to disable PD message delivery. The TCPC clears the `RECEIVE_DETECT` and `READABLE_BYTE_COUNT` registers to disable the PD message delivery.
B6	`Enable Cable Reset`	R/W	`0b`	`0b`: TCPC does not detect Cable Reset signaling (default) `1b`: TCPC detects Cable Reset signaling
B5	`Enable Hard Reset`	R/W	`0b`	`0b`: TCPC does not detect Hard Reset signaling (default) `1b`: TCPC detects Hard Reset signaling
B4	`Enable SOP_DBG’’ message`	R/W	`0b`	`0b`: TCPC does not detect SOP_DBG’’ message other than SOP_DBG'' GoodCRC messages received by the sending process (default) `1b`: TCPC detects SOP_DBG’’ message
B3	`Enable SOP_DBG’ message`	R/W	`0b`	`0b`: TCPC does not detect SOP_DBG’ message other than SOP_DBG' GoodCRC messages received by the sending process (default) `1b`: TCPC detects SOP_DBG’ message
B2	`Enable SOP’’ message`	R/W	`0b`	`0b`: TCPC does not detect SOP’’ message other than SOP'' GoodCRC messages received by the sending process (default) `1b`: TCPC detects SOP’’ message

`RECEIVE_DETECT` (`0x2F`) — continued

Table 36. RECEIVE_DETECT Register (Cont.)

Bits	Field	Access	Default	Description
`B1`	`Enable SOP’ message`	R/W	`0b`	0b: TCPC does not detect SOP’ message other than SOP' GoodCRC messages received by the sending process (default) 1b: TCPC detects SOP’ message
`B0`	`Enable SOP message`	R/W	`0b`	0b: TCPC does not detect SOP message other than SOP GoodCRC messages received by the sending process (default) 1b: TCPC detects SOP message

7.2.28 `READABLE_BYTE_COUNT` (30h)

Address: 30h | Reset Value: 00h | Access: R

Table 37. READABLE_BYTE_COUNT

Bits	Field	Access	Default	Description
`B7..0`	`READABLE_BYTE_COUNT`	R	`00h`	Indicates the number of bytes in the `RX_BUF_BYTE_x` registers plus one (for the `RX_BUF_FRAME_TYPE`). The content of this register is undefined when the `RECEIVE_BUFFER` is cleared. The value in this register is less than or equal to 81 in the case of supporting the proprietary long message or 133 in the case of supporting the TCPCI standard long message.

7.2.29 `RX_BUF_FRAME_TYPE`

Reset value: 00h — Access: R

Table 38. RX_BUF_FRAME_TYPE

Bits	Field	Access	Default	Description
`B7..3`	`Reserved`	R	`00000b`	Set to zero by sender and ignored by receiver.
`B2..0`	`Received SOP* Message`	R	`000b`	000b: Received SOP 001b: Received SOP’ 010b: Received SOP’’ 011b: Received SOP_DBG’ 100b: Received SOP_DBG’’ 110b: Received Cable Reset All others are reserved.

7.2.30 `RX_BUF_BYTE_x`

`RX_BUFFER_DATA` (`RX_BUF_BYTE_x`)

Reset value: 00h — Access: R

Table 39. RX_BUFFER_DATA Register

Bits	Field	Access	Default	Description
`B7..0`	`Rx Buffer`	R	`00h`	The TCPM reads the `READABLE_BYTE_COUNT` to determine the number of bytes in the `RX_BUFFER_DATA`. The TCPM then reads the content of the USB PD message in `RX_BUFFER_DATA`.

7.2.31 `TRANSMIT` (50h)

Address: 50h | Reset Value: 00h | Access: R/W

Table 40. TRANSMIT Register

Bits	Field	Access	Default	Description
`B7..6`	`Reserved`	R	`00b`	Set to zero by sender and ignored by receiver.
`B5..4`	`Retry Counter`	R/W	`00b`	00b: No message retry is required 01b: Automatically retry message transmission once 10b: Automatically retry message transmission twice 11b: Automatically retry message transmission three times
`B3`	`Reserved`	R	`0b`	Set to zero by sender and ignored by receiver.
`B2..0`	`Transmit SOP* message`	R/W	`000b`	000b: Transmit SOP 001b: Transmit SOP’ 010b: Transmit SOP’’ 011b: Transmit SOP_DBG’ 100b: Transmit SOP_DBG’’ 101b: Transmit Hard Reset 110b: Transmit Cable Reset 111b: Transmit BIST Carrier Mode 2 (TCPC exit the BIST mode no later than tBISTContMode max)

Note: TCPM needs to set non-zero value to RECEIVE_DETECT register prior to transmit any PD Message, Hard Reset, Cable Reset, or BIST Carrier Mode.

7.2.32 `I2C_WRITE_BYTE_COUNT`

Reset value: 00h — Access: W

Table 41. I2C_WRITE_BYTE_COUNT

Bits	Field	Access	Default	Description
`B7..0`	`I2C_WRITE_BYTE_COUNT`	W	`00h`	The number of bytes the TCPM intends to write to the `TX_BUF_BYTE_x` in the given I²C/SMBus transaction.

7.2.33 `TX_BUFFER_BYTE_x`

`TX_BUFFER_DATA` (`TX_BUFFER_BYTE_x`)

Reset value: 00h — Access: W

Table 42. TX_BUFFER_DATA Register

Bits	Field	Access	Default	Description
`B7..0`	`Tx Buffer`	W	`00h`	The TCPM writes to this register to transmit a SOP* message where the SOP* message payload (that is the header bytes and the data bytes) was written into the TCPC’s internal transmit buffer using the `TX_BUFFER_DATA` register. The value in this register is less than or equal to 80 in the case of supporting the proprietary long message or 132 in the case of supporting the TCPCI standard long message.

7.2.34 `VBUS_VOLTAGE` (70h)

Address: 70h | Reset Value: 0000h | Access: R

Table 43. VBUS_VOLTAGE Register

Bits	Field	Access	Default	Description
`B15..12`	`Reserved`	R	`0000b`	Set to zero by sender and ignored by receiver.
`B11..10`	`Scale Factor`	R	`00b`	00: VBUS measurement not scaled. 01: VBUS measurement divided by 2 10: VBUS measurement divided by 4 11: reserved This fields fixed to 00b.
`B9..0`	`VBUS voltage measurement`	R	`0000000000b`	10-bit measurement of (VBUS / Scale Factor) TCPM multiplies this value by the scale factor to obtain the voltage measurement. All voltages shows ±2% absolute value or ±50mV, whichever is greater. The LSB is 25mV. When VBUS voltage is lower than 25.6V (25mV × 1024), the Scal Factor is 00b. When VBUS voltage is higher or equal to 25.6V and lower than 51.2V (50mV × 1024), the Scale Factor is 01b. When VBUS voltage is higher or equal to 51.2V, the Scale Factor is 10b. This fields fix to 10’h0 if `POWER_CONTROL.VBUS_VOLTAGE` monitor is one.

7.2.35 `VBUS_SINK_DISCONNECT_THRESHOLD` (72h)

Address: 72h | Reset Value: 08Ch (3.5V) | Access: R/W

Table 44. VBUS_SINK_DISCONNECT_THRESHOLD Register

Bits	Field	Access	Default	Description
`B15...12`	`Reserved`	R	`0000b`	Set to 0
`B11..0`	`Voltage trip point`	R/W	`08Ch` (3.5V)	12-bit for voltage threshold with 25mV LSB. (Default 3.5V) ±5% accuracy. A value of zero disables this threshold and Sink Auto VBUS Discharge. If 51.2V (`200h`) or higher is written, it is treated as 51.15V (`1FFh`).

7.2.36 `VBUS_STOP_DISCHARGE_THRESHOLD` (74h)

Address: 74h | Reset Value: 020h (0.8V) | Access: R/W

Table 45. VBUS_STOP_DISCHARGE_THRESHOLD Register

Bits	Field	Access	Default	Description
`B15..12`	`Reserved`	R	`0000b`	Set to 0
`B11..0`	`Voltage trip point`	R/W	`020h` (0.8V)	12-bit for voltage threshold with 25mV LSB. (Default 0.8V) ±5% accuracy.

7.2.37 `VBUS_VOLTAGE_ALARM_HI_CFG` (76h)

Address: 76h | Reset Value: 000h (0V) | Access: R/W

Table 46. VBUS_VOLTAGE_ALARM_HI_CFG Register

Bits	Field	Access	Default	Description
`B15..12`	`Reserved`	R	`0000b`	Set to 0
`B11..0`	`Voltage trip point`	R/W	`000h` (0V)	12-bit for voltage threshold with 25mV LSB. ±5% accuracy.

7.2.38 `VBUS_VOLTAGE_ALARM_LO_CFG` (78h)

Address: 78h | Reset Value: 000h (0V) | Access: R/W

Table 47. VBUS_VOLTAGE_ALARM_LO_CFG Register

Bits	Field	Access	Default	Description
`B15..12`	`Reserved`	R	`0000b`	Set to 0
`B11..0`	`Voltage trip point`	R/W	`000h` (0V)	12-bit for voltage threshold with 25mV LSB. ±5% accuracy.

7.2.39 `DEVICE_CAPABILITIES_3` Register (7Ch)

Address: 7Ch | Reset Value: 110b (B2:0) | Access: R

Table 48. DEVICE_CAPABILITIES_3 Register

Bits	Field	Access	Default	Description
`B15:3`	`Reserved`	R	`0`	Set to zero by sender and ignored by receiver.
`B2:0`	`VBUS Voltage Support`	R	`110b`	RAA489400 supports 48V VBUS measurement in the TCPC VBUS Threshold and Alarm registers: `VBUS_SINK_DISCONNECT_THRESHOLD`, `VBUS_STOP_DISCHARGE_THRESHOLD`, `VBUS_VOLTAGE_ALARM_HI_CFG`, and `VBUS_VOLTAGE_ALARM_LO_CFG`. 000b: 5 Volts* 001b: 9 Volts 010b: 15 Volts 011b: 20 Volts 100b: 28 Volts 101b: 36 Volts 110b: 48 Volts 111b: Reserved. *All voltages are Nominal

Footnotes:

*All voltages are Nominal

7.2.40 `CHIP_REVISION` register (80h)

Address: 80h | Reset Value: 12h (Major 0001b, Minor 0010b) | Access: R

Table 49. CHIP_REVISION Register

Bits	Field	Access	Default	Description
`7:4`	`Major Revision Number`	R	`0001b`	Major revision number
`3:0`	`Minor Revision Number`	R	`0010b`	Minor revision number

7.2.41 `GPIO1_CTRL` Register (82h)

Address: 82h | Reset Value: 00h | Access: R/W

Table 50. GPIO1_CTRL Register

Bits	Field	Access	Default	Description
`7:5`	`Reserved`	R	`0b`	Set to zero by sender and ignored by receiver.
`4`	`GPIO1_IE`	R/W	`0b`	GPIO1 Input Enable 0b: GPIO1 input is disabled and `GPIO1_I` is held 0b regardless of GPIO1 pin condition. 1b: GPIO1 input is enabled.
`3`	`GPIO1_OD_N`	R/W	`0b`	GPIO1 Push-pull / Open-drain select 0b: GPIO1 output is open-drain. 1b: GPIO1 output is push-pull.
`2`	`GPIO1_OE`	R/W	`0b`	GPIO1 Output Enable 0b: GPIO1 output is disabled and Hi-Z. 1b: GPIO1 output is enabled and pin state follows setting of `GPIO1_O`.
`1`	`GPIO1_O`	R/W	`0b`	GPIO1 Output Data 0b: GPIO1 pin is driven low. 1b: GPIO1 pin is driven high (`GPIO1_OD_N`=1b) or Hi-Z (`GPIO1_OD_N`=0b).
`0`	`GPIO1_I`	R	`0b`	GPIO1 Input Data 0b: GPIO1 pin input state is low. 1b: GPIO1 pin input state is high. `GPIO1_OE` should be 0b when reading GPIO1 pin state, which is driven by external device. When `GPIO1_OE` is 1b, driven data by `GPIO1_O` can be read back.

7.2.42 `GPIO2_CTRL` Register (83h)

Address: 83h | Reset Value: 00h | Access: R/W

Table 51. GPIO2_CTRL Register

Bits	Field	Access	Default	Description
`7:5`	`Reserved`	R	`0b`	Set to zero by sender and ignored by receiver.
`4`	`GPIO2_IE`	R/W	`0b`	GPIO2 Input Enable 0b: GPIO2 input is disabled and `GPIO2_I` is held 0b regardless of GPIO2 pin. 1b: GPIO2 input is enabled
`3`	`GPIO2_OD_N`	R/W	`0b`	GPIO2 Push-pull / Open-drain select 0b: GPIO2 output is open-drain. 1b: GPIO2 output is push-pull.
`2`	`GPIO2_OE`	R/W	`0b`	GPIO2 Output Enable 0b: GPIO2 output is disabled and Hi-Z. 1b: GPIO2 output is enabled and pin state follows setting of `GPIO2_O`.

Table 51. GPIO2_CTRL Register (Cont.)

Bits	Field	Access	Default	Description
`1`	`GPIO2_O`	R/W	`0b`	GPIO2 Output Data 0b: GPIO2 pin is driven low. 1b: GPIO2 pin is driven high (`GPIO2_OD_N` = 1b) or Hi-Z (`GPIO2_OD_N` = 0b).
`0`	`GPIO2_I`	R	`0b`	GPIO2 Input Data 0b: GPIO2 pin input state is low. 1b: GPIO2 pin input state is high. `GPIO2_OE` should be 0b when reading GPIO2 pin state, which is driven by external device. When `GPIO2_OE` is 1b, driven data by `GPIO2_O` can be read back.

7.2.43 `GPIO3_CTRL` Register (84h)

Address: 84h | Reset Value: 00h | Access: R/W

Table 52. GPIO3_CTRL Register

Bits	Field	Access	Default	Description
`7:5`	`Reserved`	R	`0b`	Set to zero by sender and ignored by receiver.
`4`	`GPIO3_IE`	R/W	`0b`	GPIO3 Input Enable 0b: GPIO3 input is disabled and `GPIO3_I` is held 0b regardless of GPIO3 pin. 1b: GPIO3 input is enabled
`3`	`GPIO3_OD_N`	R/W	`0b`	GPIO3 Push-pull / Open-drain select 0b: GPIO3 output is open-drain. 1b: GPIO3 output is push-pull.
`2`	`GPIO3_OE`	R/W	`0b`	GPIO3 Output Enable 0b: GPIO3 output is disabled and Hi-Z. 1b: GPIO3 output is enabled and pin state follows setting of `GPIO3_O`.
`1`	`GPIO3_O`	R/W	`0b`	GPIO3 Output Data 0b: GPIO3 pin is driven low. 1b: GPIO3 pin is driven high (`GPIO3_OD_N` = 1b) or Hi-Z (`GPIO3_OD_N` = 0b).
`0`	`GPIO3_I`	R	`0b`	GPIO3 Input Data 0b: GPIO3 pin input state is low. 1b: GPIO3 pin input state is high. `GPIO3_OE` should be 0b when reading GPIO3 pin state which is driven by external device. When `GPIO3_OE` is 1b, driven data by `GPIO3_O` can be read back.

7.2.44 `GPIO4_CTRL` Register (85h)

Address: 85h | Reset Value: 00h | Access: R/W

Table 53. GPIO4_CTRL Register

Bits	Field	Access	Default	Description
`7:5`	`Reserved`	R	`0b`	Set to zero by sender and ignored by receiver.
`4`	`GPIO4_IE`	R/W	`0b`	GPIO4 Input Enable 0b: GPIO4 input is disabled and `GPIO4_I` is held 0b regardless of GPIO4 pin. 1b: GPIO4 input is enabled
`3`	`GPIO4_OD_N`	R/W	`0b`	GPIO4 Push-pull / Open-drain select 0b: GPIO4 output is open-drain. 1b: GPIO4 output is push-pull.
`2`	`GPIO4_OE`	R/W	`0b`	GPIO4 Output Enable 0b: GPIO4 output is disabled and Hi-Z. 1b: GPIO4 output is enabled and pin state follows setting of `GPIO4_O`.
`1`	`GPIO4_O`	R/W	`0b`	GPIO4 Output Data 0b: GPIO4 pin is driven low. 1b: GPIO4 pin is driven high (`GPIO4_OD_N` = 1b) or Hi-Z (`GPIO4_OD_N` = 0b).
`0`	`GPIO4_I`	R	`0b`	GPIO4 Input Data 0b: GPIO4 pin input state is low. 1b: GPIO4 pin input state is high. `GPIO4_OE` should be 0b when reading GPIO4 pin state which is driven by external device. When `GPIO4_OE` is 1b, driven data by `GPIO4_O` can be read back.

7.2.45 `VBUS_PATH_CTRL` Register (86h)

Address: 86h | Reset Value: 00h | Access: R/W

Table 54. VBUS_PATH_CTRL Register

Bits	Field	Access	Default	Description
`7:5`	`VBUS_SRC_SEL`	R/W	`000b`	VBUS Source Path Control Select 000b: VSRC_GATE 001b: GPIO1 010b: GPIO2 011b: GPIO3 100b: GPIO4 Others: Reserved It is ignored when `VBUS_SRC_EN` = 0b.
`4`	`VBUS_SRC_EN`	R/W	`0b`	VBUS Source Path Control Enable 0b: VBUS source path control is disabled. 1b: VBUS source path control is enabled.

Table 54. VBUS_PATH_CTRL Register (Cont.)

Bits	Field	Access	Default	Description
`3:1`	`VBUS_SNK_SEL`	R/W	`000b`	VBUS Sink Path Control Select 000b: VSNK_GATE 001b: GPIO1 010b: GPIO2 011b: GPIO3 100b: GPIO4 Others: Reserved It is ignored when `VBUS_SNK_EN` = 0b.
`0`	`VBUS_SNK_EN`	R/W	`0b`	VBUS Sink Path Control Enable 0b: VBUS sink path control is disabled. 1b: VBUS sink path control is enabled.

7.2.46 `VBUS_GPIO_CTRL` Register (87h)

Address: 87h | Reset Value: 00h | Access: R/W

Table 55. VBUS_GPIO_CTRL Register

Bits	Field	Access	Default	Description
`7:6`	`Reserved`	R	`0b`	Set to zero by sender and ignored by receiver.
`5`	`EN_SRC`	R/W	`0b`	GPIOn_O Setting of Enable Source Value of this bit is loaded to `GPIOn_O` where n is `VBUS_SRC_SEL` of `VBUS_PATH_CTRL` register, when VBUS Source Path is enabled, for example, receiving SourceVbusDefaultVoltage command, or detecting FRS VBUS ON condition. `GPIOn_OE` is set to one and `GPIOn_OD_N` is unchanged when `GPIOn_O` is loaded. Loaded values can be read from `GPIOn_CTRL` register. It is ignored when `VBUS_SRC_SEL` is 000b.
`4`	`DIS_SRC`	R/W	`0b`	GPIOn_O Setting of Disable Source Value of this bit is loaded to `GPIOn_O` where n is `VBUS_SRC_SEL` of `VBUS_PATH_CTRL` register, when VBUS Source Path is disabled, for example, receiving DisableSourceVbus command or detecting VBUS fault condition. `GPIOn_OE` is set to one and `GPIOn_OD_N` is unchanged when `GPIOn_O` is loaded. Loaded values can be read from `GPIOn_CTRL` register. It is ignored when `VBUS_SRC_SEL` is 000b.
`3:2`	`Reserved`	R	`0b`	-

`VBUS_GPIO_CTRL` (`0x87`) — continued

Table 55. VBUS_GPIO_CTRL Register (Cont.)

Bits	Field	Access	Default	Description
1	`EN_SNK`	R/W	`0b`	GPIOn_O Setting of Enable Sink Value of this bit is loaded to GPIOn_O where n is `VBUS_SNK_SEL` of `VBUS_PATH_CTRL` register, when VBUS Sink Path is enabled, for example, receiving SinkVbus command. GPIOn_OE is set to one and GPIOn_OD_N is unchanged when GPIOn_O is loaded. Loaded values can be read from `GPIOn_CTRL` register. It is ignored when `VBUS_SNK_SEL` is `000b`.
0	`DIS_SNK`	R/W	`0b`	GPIOn_O Setting of Disable Sink Value of this bit is loaded to GPIOn_O where n is `VBUS_SNK_SEL` of `VBUS_PATH_CTRL` register, when VBUS Sink Path is disabled, for example, receiving DisableSinkVbus command, detecting VBUS fault condition or detecting FRS VBUS OFF condition. GPIOn_OE is set to one and GPIOn_OD_N is unchanged when GPIOn_O is loaded. Loaded values can be read from `GPIOn_CTRL` register. It is ignored when `VBUS_SNK_SEL` is `000b`.

7.2.47 VBUS_CP_CTRL Register (88h)

Address: 88h | Reset Value: 00h (all bits reset to 0b) | Access: R/W (bits 7:2 and 0 are R)

Table 56. VBUS_CP_CTRL Register

Bits	Field	Access	Default	Description
7:2	Reserved	R	`0b`	Set to zero by sender and ignored by receiver.
1	`VSRC_CP_EN`	R/W	`0b`	VSRC_GATE Charge pump Enable Since it takes tens of ms that the charge pump generates high voltage, TCPM enables the charge pump before turning on VSRC_GATE. TCPM might enable the charge pump in the AttachWait.SRC state, and can disable it when leaving from the Attached.SRC state. `0b`: VSRC_GATE charge pump is disabled. `1b`: VSRC_GATE charge pump is enabled. Note: When Sink FRS is enabled with Fast Role Swap Enable in POWER CONTROL register, TCPM sets this bit.
0	Reserved	R	`0b`	Set to zero by sender and ignored by receiver.

7.2.48 GPIO_OC_EN Register (89h)

Address: 89h | Reset Value: 00h (all bits reset to 0b) | Access: R/W (bits 7:4 are R)

Table 57. GPIO_OC_EN Register

Bits	Field	Access	Default	Description
7:4	Reserved	R	`0b`	Set to zero by sender and ignored by receiver.
3	`GPIO4 OC# EN`	R/W	`0b`	GPIO4 OC# Enable `0b`: GPIO4 OC# input is disabled. `1b`: GPIO4 OC# input is enabled. When it is set to `1b` and GPIO4_OE is set to `0b`, GPIO4 pin acts as OC# input. Overcurrent is detected if GPIO4 pin is low. TCPM can manually set GPIO4_OE = `1b`, GPIO4_OD_N = `0b` and GPIO4_O = `0b` to use GPIO4 pin as OC# output.
2	`GPIO3 OC# EN`	R/W	`0b`	GPIO3 OC# Enable `0b`: GPIO3 OC# input is disabled. `1b`: GPIO3 OC# input is enabled. When it is set to `1b` and GPIO3_OE is set to `0b`, GPIO3 pin acts as OC# input. Overcurrent is detected if GPIO3 pin is low. TCPM can manually set GPIO3_OE = `1b`, GPIO3_OD_N = `0b` and GPIO3_O = `0b` to use GPIO3 pin as OC# output.
1	`GPIO2 OC# EN`	R/W	`0b`	GPIO2 OC# Enable `0b`: GPIO2 OC# input is disabled. `1b`: GPIO2 OC# input is enabled. When it is set to `1b` and GPIO2_OE is set to `0b`, GPIO2 pin acts as OC# input. Overcurrent is detected if GPIO2 pin is low. TCPM can manually set GPIO2_OE = `1b`, GPIO2_OD_N = `0b` and GPIO2_O = `0b` to use GPIO2 pin as OC# output.
0	`GPIO1 OC# EN`	R/W	`0b`	GPIO1 OC# Enable `0b`: GPIO1 OC# input is disabled. `1b`: GPIO1 OC# input is enabled. When it is set to `1b` and GPIO1_OE is set to `0b`, GPIO1 pin acts as OC# input. Overcurrent is detected if GPIO1 pin is low. TCPM can manually set GPIO1_OE = `1b`, GPIO1_OD_N = `0b` and GPIO1_O = `0b` to use GPIO1 pin as OC# output.

7.2.49 VBUS_CTRL Register (90h)

Address: 90h | Reset Value: per-bit (see table) | Access: R/W (Reserved bits are R; RESET_AVERAGE and RESET_PEAK are W)

Table 58. VBUS_CTRL Register

Bits	Field	Access	Default	Description
15	Reserved	R	`0b`	Set to zero by sender and ignored by receiver.
14:12	`N3`	R/W	`000b`	N3. Refer to VBUS Current Measurement. TCPM should not set zero to N3 or at least MSB of N3 (Bit[14]) when `AVERAGE_EN` is set to one. Setting zero is undefined when `AVERAGE_EN` is set to one.
11	Reserved	R	`0b`	Set to zero by sender and ignored by receiver.
10:8	`N4`	R/W	`0000b`	N4. Refer to VBUS Current Measurement.

Table 58. VBUS_CTRL Register (Cont.)

Bits	Field	Access	Default	Description
7	`RESET_AVERAGE`	W	`0b`	Reset Stored Average VBUS Current It is write only bit, and zero will be read. When one is written, `VBUS_AVE_CURRENT` register is cleared to zero, and start to measure new average current value over the TIME_INTERVALif `AVERAGE_EN` is one. When zero is written, it has no effect.
6	`AVERAGE_EN`	R/W	`0b`	Enable Average VBUS Current Measurement `0b`: Disabled `1b`: Enabled When the `AVERAGE_EN` = 1, it enables calculating an average of VBUS Current and `VBUS_AVE_CURRENT` register is kept updated whenever new average value is calculated. When this bit is set to zero, `VBUS_AVE_CURRENT` register holds the last value until `RESET_AVERAGE` is set to one or Disable VBUS_CURRENT Monitor is set to one.
5	`RESET_PEAK`	W	`0b`	Reset Stored Peak VBUS Current It is write only bit, and zero will be read. When one is written, `VBUS_PEAK_CURRENT` register is cleared to zero, and start to measure new peak current value if `PEAK_EN` is one. When zero is written, it has no effect.
4	`PEAK_EN`	R/W	`0b`	Enable Peak VBUS Current Measurement `0b`: Disabled `1b`: Enabled When `PEAK_EN` = 1, it enables to recode peak VBUS current value, and `VBUS_PEAK_CURRENT` register is kept updated whenever new peak current value is detected. When this bit is set to zero, `VBUS_PEAK_CURRENT` register holds the last value until `RESET_PEAK` is set to one or Disable VBUS_CURRENT Monitor is set to one.

Table 58. VBUS_CTRL Register (Cont.)

Bits	Field	Access	Default	Description
3:2	`TIME_INTERVAL`	R/W	`00b`	VBUS ADC Time Interval It selects sampling interval of ADC. Every sampling interval, if both VBUS_VOLTAGE Monitor of `POWER_COTNROL` register and Disable VBUS_CURRENT Monitor of this register are set to `0b` (that is monitor function is enabled), source of ADC is alternating between VBUS voltage and VBUS current at the half of the interval. So that VBUS voltage and VBUS current are sampled every interval which is set to this field. If either one of Disable VBUS_VOLTAGE Monitor or Disable VBUS_CURRENT Monitor is set to `0b`, only the enabled one is sampled at the every interval. Between the interval, the ADC function is disabled to save power. The ADC is disabled entirely if both Disable VBUS_VOLTAGE Monitor and Disable VBUS_CURRENT Monitor are set to `1b`. Sampled VBUS voltage is read from `VBUS_VOLTAGE` register, and sampled VBUS current is read from `VBUS_CURRENT` register. `00b`: 5ms `01b`: 10ms `10b`: 15ms `11b`: 20ms
1	Reserved	R	`0b`	Set to zero by sender and ignored by receiver.
0	Disable VBUS_CURRENT Monitor	R/W	`1b`	`0b`: VBUS_CURRENT Monitoring is enabled. `VBUS_CURRENT` register is updated every interval set by `TIME_INTERVAL` of this register. `1b`: VBUS_CURRENT Monitoring is disabled. When this bit is `1b`, all other bits in this register, `VBUS_CURRENT`, `VBUS_AVE_CURRENT` and VBUS_PEAK_CURRENTare invalid. `VBUS_AVE_CURRENT` and `VBUS_PEAK_CURRENT` can be cleared by setting one to `RESET_AVERAGE` or `RESET_PEAK`.

7.2.50 VBUS_CURRENT Register (92h)

Address: 92h | Reset Value: per-bit (see table) | Access: R

Table 59. VBUS_CURRENT Register^[1]

Bits	Field	Access	Default	Description
15	Direction	R	`0b`	`0b`: Sink `1b`: Source
14:10	Reserved	R	`0b`	Set to zero by sender and ignored by receiver.
9:0	`VBUS_CURRENT`	R	`000000000b`	VBUS Current LSB is 11.574mA.

This register is cleared when the Disable VBUS_CURRENT Monitor bit of the VBUS_CTRL register is set to 1b.

7.2.51 VBUS_PEAK_CURRENT Register (94h)

Address: 94h | Reset Value: per-bit (see table) | Access: R

Table 60. VBUS_PEAK_CURRENT Register^[1]

Bits	Field	Access	Default	Description
15:10	Reserved	R	`0b`	Set to zero by sender and ignored by receiver.
9:0	`VBUS_PEAK_CURRENT`	R	`000000000b`	VBUS Peak Current LSB is 11.574mA.

This register is cleared when the Disable VBUS_CURRENT Monitor bit of the VBUS_CTRL register is set to 1b.

7.2.52 VBUS_AVE_CURRENT Register (96h)

Address: 96h | Reset Value: per-bit (see table) | Access: R

Table 61. VBUS_AVE_CURRENT Register^[1]

Bits	Field	Access	Default	Description
15:10	Reserved	R	`0b`	Set to zero by sender and ignored by receiver.
9:0	`VBUS_AVE_CURRENT`	R	`000000000b`	VBUS Average Current It shows the Integer part of y_n in 5.3.6.2. Refer to 5.3.6.2 for more detail LSB is 11.574mA.

This register is cleared when the Disable VBUS_CURRENT Monitor bit of the VBUS_CTRL register is set to 1b.

7.2.53 FRS_CTRL Register (98h)

Address: 98h | Reset Value: 40h (VBUS_FRS = 01b, all other bits 0b) | Access: R/W

Table 62. FRS_CTRL Register

Bits	Field	Access	Default	Description
7:6	`VBUS_FRS`	R/W	`01b`	VBUS Voltage Threshold to turn off VBUS Sink Path if `SNK_OFF_SEL` = `1b` and to turn on VBUS Source Path. It does not affect VBUS Sink Path when `SNK_OFF_SELECT` is set to `0b`. `00b`: 5.2V `01b`: 5.5V `10b`: 5.8V `11b`: Reserved
5:1	`SNK_TO_SRC_TIMER`	R/W	`00000b`	VBUS Sink Off to Source On Timer VBUS Source path, VSRC_GATE or GPIO, is turned on after SNK_TO_SRC_TIMERON × 4µs of turning off VBUS Sink Path, or detecting VBUS < `VBUS_FRS` whichever comes later. If VBUS Sink Path is already off when FRS signal is received, it is treated as this timer is expired to turn on VBUS Source Path when VBUS < `VBUS_FRS` is detected. `00000b`: 0µs `00001b`: 4µs `00010b`: 8µs … `11111b`: 124µs Note: Actual interval time is 0 to 2.67μs longer than the setting, for example, actual time is 4.0 to 6.67µs when set to 4µs.

Table 62. FRS_CTRL Register (Cont.)

Bits	Field	Access	Default	Description
0	`SNK_OFF_SEL`	R/W	`0b`	VBUS Sink Off Trigger VBUS Sink Path, VSNK_GATE or GPIO, is turned off when either condition is detected. `0b`: FRS Signal is received. `1b`: FRS Signal has been received and VBUS < VBUS_FRS_SNK is detected.

7.2.54 SINK_PATH_DISCHG Register (9Ah)

Address: 9Ah | Reset Value: 00h (all bits reset to 0b) | Access: R/W (bits 7:4 are R)

Table 63. SINK_PATH_DISCHG Register

Bits	Field	Access	Default	Description
7:4	Reserved	R	`0h`	Set to zero by sender and ignored by receiver.
3:2	`DISCHG_TIMEOUT`	R/W	`00b`	`00b`:150ms `01b`:200ms `10b`:250ms `11b`:300ms
1	`MANUAL_DISCHG`	R/W	`0b`	Manual Discharge Trigger `0b`: Manual Discharge is not triggered. `1b`: Start Manual Discharge. Once voltage of SINK_DISCHG pin reaches vSafe5V(max) or DISCHARGE_TIMEOUT is expired, discharging is stopped and this bit is cleared to zero.
0	`DISCHG_MODE`	R/W	`0b`	Select a mode of Sink Path Discharge `0b`: Manual Discharge. `1b`: Automatic Discharge.

7.2.55 SNK_DETACH Register (9Bh)

Address: 9Bh | Reset Value: 00h (all bits reset to 0b) | Access: R/W (bits 7:5 are R)

Table 64. SNK_DETACH Register

Bits	Field	Access	Default	Description
7:5	Reserved	R	`000b`	Set to zero by sender and ignored by receiver.
4	`AUTO_DISCHG_SNK_OPEN`	R/W	`0b`	`0b`: VBUS is not automatically discharged when Sink Disconnect condition of SNK.Open is detected. TCPM needs to set `0b` to this bit.
3:0	`SNK_OPEN`	R/W	`0000b`	`0000b`: PROCHOT# assertion is disabled for Sink Detach detected by CC lines. `0001b` to `1111b`: PROCHOT# is asserted when this field is set to non-zero value, `SNK_DETACH_EN` of `PROCHOT_EN` register is set to `1b`, and `SNK_DETACH_PROCHOT` of `VENDOR_STATUS` register is set to `1b`.

7.2.56 VENDOR_STATUS Register (A0h)

Address: A0h | Reset Value: 0000h (all bits reset to 0b) | Access: R/W1C (bits 8:7 and 5 are R)

Table 65. VENDOR_STATUS Register

Bits	Field	Access	Default	Description
15	Sink path discharge timeout	R/W1C	`0b`	`0b`: Not timed out yet to discharge or not started to discharge `1b`: Not completed to discharge internal sink path within a setting in `SINK_PATH_DISCHARGE_CTRL`.Bit3:2
14	Sink path discharge completion	R/W1C	`0b`	`0b`: Not completed to discharge or not started to discharge `1b`: Completed to discharge either internal sink path voltage transitions below vSafe5V or the voltage does not transition below vSafe5V after the timeout setting in `SINK_PATH_DISCHARGE_CTRL`.Bit3:2
13	`VCONN_OTP`	R/W1C	`0b`	`0b`: `VCONN_OTP_DIS` of `VCONN_FAULT_CTRL` register is `1b` or VCONN OTP has not been occurred. `1b`: `VCONN_OTP_DIS` of `VCONN_FAULT_CTRL` register is `0b` and VCONN OTP has been occurred. This bit remains `1b` even if TCPM writes `1b` to this bit when VCONN over temperature condition still occurs.
12	`VCONN_RVP`	R/W1C	`0b`	`0b`: `VCONN_RVP_DIS` of `VCONN_FAULT_CTRL` register is `1b` or VCONN RVP has not been occurred. `1b`: `VCONN_RVP_DIS` of `VCONN_FAULT_CTRL` register is `0b` and VCONN RVP has been occurred. This bit remains `1b` even if TCPM writes `1b` to this bit when VCONN Reverse voltage condition still occurs.
11	`VCONN_UVP`	R/W1C	`0b`	`0b`: `VCONN_UVP_DIS` of `VCONN_FAULT_CTRL` register is `1b` or VCONN UVP has not been occurred. `1b`: `VCONN_UVP_DIS` of `VCONN_FAULT_CTRL` register is `0b` and VCONN UVP has been occurred. This bit remains `1b` even if TCPM writes `1b` to this bit when VCONN Under voltage condition still occurs.
10	`VCONN_OVP`	R/W1C	`0b`	`0b`: `VCONN_OVP_DIS` of `VCONN_FAULT_CTRL` register is `1b` or VCONN OVP has not been occurred. `1b`: `VCONN_OVP_DIS` of `VCONN_FAULT_CTRL` register is `0b` and VCONN OVP has been occurred. This bit remains `1b` even if TCPM writes `1b` to this bit when VCONN Overvoltage condition still occurs.
9	`VCONN_0p8V`	R/W1C	`0b`	`0b`: VCONN is has not been changed below 0.8V. `1b`: VCONN has been changed below 0.8V. This bit is intended to indicate when VCONN discharge is completed in order to show VCONN status even if the Enable VCONN bit of the `POWER_CONTROL` register is set to `0b`.
8:7	Reserved	R	`00b`	Set to zero by sender and ignored by receiver.
6	`FAULT_STATE_CHANGED`	RW1C	`0b`	`0b`: `FAULT_STATE` bit is not changed since last time TCPM wrote `1b` to this bit. `1b`: `FAULT_STATE` bit is changed since last time TCPM wrote `1b` to this bit.
5	`FAULT_STATE`	R	`0b`	`0b`: RAA489400 is not in the FAULT state. `1b`: RAA489400 is in the FAULT state.

Table 65. VENDOR_STATUS Register (Cont.)

Bits	Field	Access	Default	Description
4	`SRC_VBUS_RVP`	R/W1C	`0b`	`0b`: `SRC_VBUS_RVP_DIS` of `VBUS_FAULT_CTRL` register is `1b` or SRC VBUS RVP has not been occurred. `1b`: `SRC_VBUS_RVP_DIS` of `VBUS_FAULT_CTRL` register is `0b` and SRC VBUS RVP has been occurred. This bit remains `1b` even if TCPM writes `1b` to this bit when Source VBUS Reverse voltage condition still occurs.
3	`SRC_VBUS_UVP`	R/W1C	`0b`	`0b`: `SRC_VBUS_UVP_DIS` of `VBUS_FAULT_CTRL` register is `1b` or SRC VBUS UVP has not been occurred. `1b`: `SRC_VBUS_UVP_DIS` of `VBUS_FAULT_CTRL` register is `0b` and SRC VBUS UVP has been occurred. This bit remains `1b` even if TCPM writes `1b` to this bit when Source VBUS Under voltage condition still occurs.
2	Reserved	R	`0b`	Set to zero by sender and ignored by receiver.
1	`SNK_DETACH_PROCHOT`	R/W1C	`0b`	`0b`: Sink Detach by SNK.Open has not been detected. `1b`: Sink Detach by SNK.Open has been detected. Writing one to this bit clears the bit to zero. If bit 0 of `ALERT_EXTENDED` register and bit 1 of this register are zero, PROCHOT# is deasserted (Hi-Z). Sink Detach is detected when: SNK.Open is detected on the monitored CC for more than 40μs. Note: It is different form the method defined in the `SNK_DETACH` register.
0	`SNK_DETACH`	R/W1C	`0b`	TCPM needs to clear this bit when TCPM clears other bit in this register.

7.2.57 `VENDOR_STATUS_ALERT_MASK` Register (`A2h`)

Address: A2h | Reset Value: per-bit (see table) | Access: R/W (Reserved bits: R)

Table 66. VENDOR_STATUS_ALERT_MASK Register

Bits	Field	Access	Default	Description
15	Sink path discharge timeout	R/W	`0b`	0b: Interrupt masked 1b: Interrupt unmasked
14	Sink path discharge completion	R/W	`0b`	0b: Interrupt masked 1b: Interrupt unmasked
13	`VCONN_OTP`	R/W	`0b`	0b: Interrupt masked 1b: Interrupt unmasked
12	`VCONN_RVP`	R/W	`0b`	0b: Interrupt masked 1b: Interrupt unmasked
11	`VCONN_UVP`	R/W	`0b`	0b: Interrupt masked 1b: Interrupt unmasked
10	`VCONN_OVP`	R/W	`0b`	0b: Interrupt masked 1b: Interrupt unmasked
9	`VCONN_0p8V`	R/W	`0b`	0b: Interrupt masked 1b: Interrupt unmasked
8:7	Reserved	R	`00b`	Set to zero by sender and ignored by receiver.
6	`FAULT_STATE_CHANGED`	R/W	`0b`	0b: Interrupt masked 1b: Interrupt unmasked
5	Reserved	R	`0b`	Set to zero by sender and ignored by receiver.
4	`SRC_VBUS_RVP`	R/W	`0b`	0b: Interrupt masked 1b: Interrupt unmasked
3	`SRC_VBUS_UVP`	R/W	`0b`	0b: Interrupt masked, 1b: Interrupt unmasked
2	Reserved	R	`0b`	Set to zero by sender and ignored by receiver.
1	`SNK_DETACH_PROCHOT`	R/W	`0b`	0b: Interrupt masked 1b: Interrupt unmasked
0	`SNK_DETACH`	R/W	`0b`	TCPM needs to set 0b.

7.2.58 `VBUS_FAULT_CTRL` Register (`A4h`)

Address: A4h | Reset Value: per-bit (see table) | Access: R/W (Reserved bits: R)

Table 67. VBUS_FAULT_CTRL Register ^[1][2][3]

Bits	Field	Access	Default	Description
15:12	Reserved	R	`0000b`	Set to zero by sender and ignored by receiver.
11:8	`UVP_INACTIVE_TIME`	R/W	`0001b`	VBUS_UV/VCONN_UV detection is not activated from when VBUS/VCONN is enabled to when the time specified by this field is elapsed even if `SRC_VBUS_UVP_DIS` bit of `VBUS_FAULT_CTRL` register/`VCONN_UVP_DIS` bit of this register is 0b and VBUS/VCONN voltage is below the vVbusUv/vVconnUv threshold. This inactive time is applied also when turning on SRC Gate or GPIO in the FRS. The inactive time is 10ms multiplied by value of this field if the field is non-zero, and 160ms if the field is 0000b.

Table 67. VBUS_FAULT_CTRL Register (Cont.) ^[1][2][3]

Bits	Field	Access	Default	Description
7	`VBUS_OVP_TYPE`	R/W	`0b`	Select VBUS Overvoltage Threshold. It selects VBUS OV threshold either vSprMax or vEprMax. It also selects SRC VBUS OV threshold when `SRC_VBUS_NonDefault_OVP` (bit 6) is one. It is valid only when VBUS Overvoltage Fault bit (B1) is set to 1b in `FAULT_CONTROL` Register. 0b: VBUS OVP Threshold is vSprMax 1b: VBUS OVP Threshold is vEprMax
6	`SRC_VBUS_NonDefault_OVP`	RW	`0b`	0b: Use vVbusOv for SRC VBUS OVP threshold. 1b: `VBUS_OVP_TYPE` (bit 7) selects SRC VBUS OVP threshold. It is valid only when both VBUS Overvoltage of `FAULT_CONTROL` Register and `SRC_VBUS_OVP_DIS` (bit 2) are set to 0b
5	Reserved	R	`0b`	Set to zero by sender and ignored by receiver.
4	`SRC_VBUS_RVP_DIS`	R/W	`0b`	0b: SRC VBUS RVP is enabled 1b: SRC VBUS RVP is disabled Note: when `VBUS_SRC_SEL` and `VBUS_SNK_SEL` are set to same value for bi-directional VBUS path control, this bit needs to be set to 1b to disable VBUS source reverse voltage.
3	`SRC_VBUS_UVP_DIS`	R/W	`0b`	0b: SRC VBUS UVP is enabled 1b: SRC VBUS UVP is disabled Note: When system supports 5V and higher VBUS source voltage, TCPM might need to set 1b to this bit because of vVbusUv of threshold voltage.
2	`SRC_VBUS_OVP_DIS`	R/W	`0b`	0b: SRC VBUS OVP is enabled as well as SNK_VBUS_OVP 1b: SRC VBUS OVP is disabled When both VBUS Overvoltage of `FAULT_CONTROL` and this bit are set to 0b, SRC VBUS OVP is enabled. If either bit is set to 1b, SRC VBUS OVP is disabled. If SRC VBUS OVP is enabled and detected, VBUS Overvoltage of the `POWER_STATUS` register is set to 1b.
1:0	`VBUS_OC`	R/W	`01b`	VBUS Overcurrent Threshold Setting of VBUS Overcurrent Threshold. It is valid only when VBUS Overcurrent Fault bit (B2) of `FAULT_CONTROL` register is set to 1b. 00b: 1.8A 01b: 3.6A 10b: 4.8A 11b: 6.0A

Setting of this register (except for UVP_INACTIVE_TIME) and VBUS Overcurrent/Overvoltage of FAULT_CONTROL register are valid only when VBUS is turned on. When VBUS is turned off VBUS_RVP/UVP/OVP/OCP are disabled regardless of settings of this register.
SRC_VBUS_RVP and SRC_VBUS_UVP are reported in VENDOR_STATUS register.
UVP_INACTIVE_TIME is valid either when VBUS and/or VCONN is turned on or FRS is enabled.

7.2.59 `VCONN_FAULT_CTRL` Register (`A6h`)

Address: A6h | Reset Value: per-bit (see table) | Access: R/W (Reserved bits: R)

Table 68. VCONN_FAULT_CTRL Register ^[1]

Bits	Field	Access	Default	Description
7:6	Reserved	R	`0b`	Set to zero by sender and ignored by receiver.
5	`VCONN_OTP_DIS`	R/W	`0b`	0b: VCONN OTP is enabled. 1b: VCONN_OTP is disabled.
4	`VCONN_RVP_DIS`	R/W	`0b`	0b: VCONN RVP is enabled. 1b: VCONN_RVP is disabled.
3	`VCONN_UVP_DIS`	R/W	`0b`	0b: VCONN UVP is enabled. 1b: VCONN_UVP is disabled.
2	`VCONN_OVP_DIS`	R/W	`0b`	0b: VCONN OVP is enabled. 1b: VCONN_OVP is disabled.
1:0	`VCONN_OC`	R/W	`01b`	VCONN Overcurrent Threshold Setting of VCONN Overcurrent Threshold. It is valid only when VCONN Overcurrent Fault bit (B0) of `FAULT_CONTROL` register is set to 0b. 00b: 400mA 01b: 600mA 10b: 800mA 11b: Reserved

Setting of this register is valid only when VCONN is turned on. When VCONN is turned off VCONN_RVP/UVP/OVP/OTP are disabled regardless of settings of this register.

7.2.60 `OCP_OUTPUT_CTRL` Register (`A8h`)

Address: A8h | Reset Value: per-bit (see table) | Access: R/W (Reserved bits: R)

Table 69. OCP_OUTPUT_CTRL Register

Bits	Field	Access	Default	Description
15:14	Reserved	R	`0b`	Set to zero by sender and ignored by receiver.
13	`VCONN_OTP`	R/W	`0b`	0b: VCONN OTP does not assert OCP# output. 1b: OCP# is asserted when `VCONN_OTP` of `VENDOR_STATUS` register is 1b.
12	`VCONN_RVP`	R/W	`0b`	0b: VCONN RVP does not assert OCP# output. 1b: OCP# is asserted when `VCONN_RVP` of `VENDOR_STATUS` register is 1b.
11	`VCONN_UVP`	R/W	`0b`	0b: VCONN UVP does not assert OCP# output. 1b: OCP# is asserted when `VCONN_UVP` of `VENDOR_STATUS` register is 1b.
10	`VCONN_OVP`	R/W	`0b`	0b: VCONN OVP does not assert OCP# output. 1b: OCP# is asserted when `VCONN_OVP` of `VENDOR_STATUS` register is 1b.
9	Reserved	R	`0b`	Set to zero by sender and ignored by receiver.
8	`VCONN_OCP`	R/W	`0b`	0b: VCONN OCP does not assert OCP# output. 1b: OCP# is asserted when VCONN Overcurrent (B1) of `FAULT_STATUS` register is 1b.
7:5	Reserved	R	`000b`	Set to zero by sender and ignored by receiver.

Table 69. OCP_OUTPUT_CTRL Register (Cont.)

Bits	Field	Access	Default	Description
4	`VBUS_RVP`	R/W	`0b`	0b: VBUS RVP does not assert OCP# output. 1b: OCP# is asserted when `VBUS_RVP` of `VENDOR_STATUS` register is 1b.
3	`VBUS_UVP`	R/W	`0b`	0b: VBUS UVP does not assert OCP# output. 1b: OCP# is asserted when `VBUS_UVP` of `VENDOR_STATUS` register is 1b.
2	`VBUS_OVP`	R/W	`0b`	0b: VBUS OVP does not assert OCP# output. 1b: OCP# is asserted when VBUS Overvoltage (B2) of `FAULT_STATUS` register is 1b.
1	Reserved	R	`0b`	Set to zero by sender and ignored by receiver.
0	`VBUS_OCP`	R/W	`0b`	0b: VBUS OCP does not assert OCP# output. 1b: OCP# is asserted when VBUS Overcurrent (B3) of `FAULT_STATUS` register is 1b.

7.2.61 `PROCHOT_EN` Register (`AAh`)

Address: AAh | Reset Value: per-bit (see table) | Access: R/W (Reserved bits: R)

Table 70. PROCHOT_EN Register

Bits	Field	Access	Default	Description
7:2	Reserved	R	`00000b`	Set to zero by sender and ignored by receiver.
1	`SNK_DETACH_EN`	R/W	`0b`	0b: Detecting Sink Detach by SNK.Open, that is, setting `SNK_DETACH_PROCHOT` bit of `VENDOR_STATUS` register to 1b, does not assert PROCHOT#. 1b: Detecting Sink Detach by SNK.Open, that is, setting `SNK_DETACH_PROCHOT` of `VENDOR_STATUS` register to 1b, asserts PROCHOT#. Sink Detach is detected when: SNK.Open is detected on the monitored CC for more than 40μs. Note that it is different form the method defined in the `SNK_DETACH` register
0	`FRS_EN`	R/W	`0b`	0b: Receiving FRS Signal, that is, setting Sink Fast Role Swap bit of `ALERT_EXTENDED` register to 1b, does not assert PROCHOT#. 1b: Receiving FRS Signal, that is, setting Sink Fast Role Swap bit of `ALERT_EXTENDED` register to 1b, asserts PROCHOT#.

7.2.62 `Control1` Register (`B1h`)

Address: B1h | Reset Value: per-bit (see table) | Access: R/W

Table 71. Control1 Register

Bits	Field	Access	Default	Description
15:3	Reserved	R/W	`0h`	Must be set to zero.
2:0	Oscillator Calibration Setting	R/W	`000b`	Must be set to 001b.

7.2.63 `TYPE_C_PRAMETER` Register (`E2h`)

Address: E2h | Reset Value: per-bit (see table) | Access: R/W (Reserved bits: R or R/W as noted)

Table 72. TYPE_C_PARAMETER Register

Bits	Field	Access	Default	Description
15	Reserved	R/W	`0b`	Set to zero.
14	Force Enable 24MHz Clock operation	R/W	`0b`	0b: Enabled automatic power saving 1b: Disabled automatic power saving Before starts to transmit BIST message, this field must be set to 1b. For other cases, this field must be set to 0b for power saving.
13	Stop 24MHz OSC	R/W	`0b`	0b: 24MHz OSC is enabled. 1b: 24MHz OSC is disabled. When CC1/CC2 status is changed or I²C access is received, 24MHz OSC is enabled again automatically and this bit is cleared to 0b.
12:9	Reserved	R	`0000b`	Set to zero by sender.
8:2	Reserved	R/W	`110 0100b`	Set to same value as Reset Value.
1:0	Reserved	R	`00b`	Set to zero by sender.

95 KiB Raw Permalink Blame History Unescape Escape

7. Registers

7.1 Register Map

7.2 Register Descriptions

7.2.1 VENDOR_ID (00h)

7.2.2 PRODUCT_ID (03h) and DEVICE_ID (04h)

DEVICE_ID (0x04)

7.2.3 USBTYPEC_REV (06h)

7.2.4 USBPD_REV_VER (08h)

7.2.5 PD_INTERFACE_REV (0Ah)

7.2.6 ALERT (10h)

7.2.7 ALERT_MASK (12h)

7.2.8 POWER_STATUS_MASK (14h)

7.2.9 FAULT_STATUS_MASK (15h)

7.2.10 EXTENDED_STATUS_MASK (16h)

7.2.11 ALERT_EXTENDED_MASK (17h)

7.2.12 TCPC_CONTROL (19h)

7.2.13 ROLE_CONTROL (1Ah)

7.2.14 FAULT_CONTROL (1Bh)

7.2.15 POWER_CONTROL (1Ch)

7.2.16 CC_STATUS (1Dh)

7.2.17 POWER_STATUS (1Eh)

7.2.18 FAULT_STATUS (0x1F)

7.2.19 EXTENDED_STATUS (0x20)

7.2.20 ALERT_EXTENDED (0x21)

7.2.21 COMMAND (0x23)

7.2.22 DEVICE_CAPABILITIES_1 (0x24)

7.2.23 DEVICE_CAPABILITIES_2 (0x26)

7.2.24 STANDARD_INPUT_CAPABILITIES (0x28)

7.2.25 STANDARD_OUTPUT_CAPABILITIES (0x29)

7.2.26 MESSAGE_HEADER_INFO (0x2E)

7.2.27 RECEIVE_DETECT (0x2F)

RECEIVE_DETECT (0x2F) — continued

7.2.28 READABLE_BYTE_COUNT (30h)

7.2.29 RX_BUF_FRAME_TYPE

7.2.30 RX_BUF_BYTE_x

RX_BUFFER_DATA (RX_BUF_BYTE_x)

7.2.31 TRANSMIT (50h)

7.2.32 I2C_WRITE_BYTE_COUNT

7.2.33 TX_BUFFER_BYTE_x

TX_BUFFER_DATA (TX_BUFFER_BYTE_x)

7.2.34 VBUS_VOLTAGE (70h)

7.2.35 VBUS_SINK_DISCONNECT_THRESHOLD (72h)

7.2.36 VBUS_STOP_DISCHARGE_THRESHOLD (74h)

7.2.37 VBUS_VOLTAGE_ALARM_HI_CFG (76h)

7.2.38 VBUS_VOLTAGE_ALARM_LO_CFG (78h)

7.2.39 DEVICE_CAPABILITIES_3 Register (7Ch)

7.2.40 CHIP_REVISION register (80h)

7.2.41 GPIO1_CTRL Register (82h)

7.2.42 GPIO2_CTRL Register (83h)

7.2.43 GPIO3_CTRL Register (84h)

7.2.44 GPIO4_CTRL Register (85h)

7.2.45 VBUS_PATH_CTRL Register (86h)

7.2.46 VBUS_GPIO_CTRL Register (87h)

VBUS_GPIO_CTRL (0x87) — continued